if u drill out all the rivets to remove the top panel, can put the rivets back ar? can use screws to replace the rivets or not?

eh? u use sunbeam thumbscrew on ur lian li! can fit ka? cause sunbeam state that it fit most cases except lian li, this is the one rite?




is this the m3 capscrews u're talking about?

[attachmentid=160792]

This post has been edited by E-J@1: Nov 30 2006, 09:30 PM

how much do ianho charge for the polishing?

can it be replaced by screw instead of the riverts? cause if can then it will make the top panel removable rite? just a thought

This post has been edited by E-J@1: Nov 30 2006, 10:00 PM

what pipe r u talking bout?

hey guys, can give me ur opinions bout this case



Official Link
Review

how bout this one too, dunno which to buy, both look damn great ,give me any their pros & cons that u can think of



Official Link
Review

not too big la, just 10cm wider & 15 shorter (in height & length) than normal atx case... any recommendation on the two case

This post has been edited by E-J@1: Dec 15 2006, 03:28 PM

yeah, seen it, reviewed it...

SS SG-01: (WxHxD) 26.3 x 21.6 x 39.3 (cm)
LL PC-V300: (WxHxD) 28 x 25 x 35.3 (cm)

just a liiiiiiillllllllll bit difference, barely u notice em...


SS TJ08: (WxHxD) 19.5 x 38.1 x 37.8 (cm)
LL PC-V600: (WxHxD) 21 x 37.1 x 49 (cm)

yeah, this u will notice the diff when it comes to their depth cause
SS onli fits m-ATX & LL fits ATX , some more LL fully alu & SS SECC...

yeah, i agree with u, if only all the m-atx will stack with full HDD bays like Soldam (isn't it going to be hot)...

FYI, i'm buying a 'sff' case for easy to carry from one place to another as i'm a varsity student, can't even seperate with my pc for a day like going back home, really piss me off if wanna carry a 10kg rig all the way up till 5th floor for every time wanna go home

This post has been edited by E-J@1: Dec 15 2006, 04:04 PM

notebook not gud enough for me who plays 24/7

nope, actually the real problem when installing it is u have to hold em when screwing it in

yup, u have to push the wire upward, but there is space for it... it's not like the drive block the wire... anyway u can put temp monitor on the top bay... that way it provides lots & lots of space for the wires

better u get the lian-li case... more cheaper... some more there a lot of room for ur cooler unlike silverstone sugo where onli cooler with max 78mm height... meanwhile for lian li, the max height for ur cooler is 115mm

Source

that i dunno, cause never state in any review i found... better ask forumer here who owns one, 1.5mm aluminum!!! not bad with its weight onli 3kg, surely it's not flimsy, does the silverstone has removable mobo tray?

btw, what cooler u using?

the lian li is around rm400, rite? and the silverstone is rm500, rite? (just curious)

yea, another lian li user in da house

just make sure ur heatsink is not taller than 10cm (to able the mobo tray to pass through the tray opening)...

remember to post some pic in here... wanna see too cause can't see any forumer owned one... maybe u'll be the first (i think)

lucky for u it can passes through... aaahhhh, if cannot also u can assemble the heatsink inside the case...

but for this PC-V600 must make very sure not to be taller than 11.5cm, otherwise it will clash with ur psu

lor, i thought it was the wire problem ... if it's too big, hmmmm , what's the problem with that !!!

yup, it's mine

ala, just buy from the bulk lor, i don't think anyone willing to sell theirs... anyway, u are not allowed to discuss this here

This post has been edited by E-J@1: Dec 23 2006, 10:01 PM

Link: http://forum.lowyat.net/topic/383875