mADmAN can i ask 1 thing? I ask at many thread also no 1 answer it.
If put the filter like yours is it will block some air flow ?

Em how bout evercool's filter fan? Because i just can get filter of this brand at Lowyat, Others brand less and less.
http://www.evercool.com.tw/products/sff_8025.htm < this 1.

Wa then everytime u need to control and take out the panel and take out the bezel and control? XD

If can maybe your fan controller need to push back abit.

akachester your Proc nad GC is is running on that temp or idle ?
My hardware temp also be like that for idle.

Now i also got problem with the fan sensor, 1 is side panel fan, 1 is front intake fan, i dont know where to put my sensor and just hanging somewhere. Maybe need install that fan control to control myself, because that sensor hanging ther although is hot or cold also run that RPM, any suggestion where to put my sensor ?

This post has been edited by vincent09: May 25 2007, 10:39 AM

Ok now i have slot the Controller ( 2 at back T-T ). need to test on tomorow afternoon ( beacause hot day, else it start raining i nothing can do. )
By detect with ai for the fan will low rpm than Lian Li case fan and my GC & CPU start hot. GC near 60ºC, cpu around 44ºC something.

I'm not sure for this, my LianLi casing, pc-60 plus, the side fan is it for exhaust GC heat or together with casing heat?

My room hard to get fresh air for my casing if without air-con. 2 pc open in 1 room quite hot. ( no include hot day. )

Wa, ATE also got sell that kind accessory O.o
Hmm don't know got sell that cable clip ( like old kind auntie wallet that kind ) or not.

My case inside got 2 there, quite nice for cable management.

This post has been edited by vincent09: May 28 2007, 09:52 PM

I see, next time go those hardware shop see. Hope can get some of them.

I need help for my lian li case. when i screw my real fan tight, the back alluminium well pop up abit, if i loss the screw, the back alluminium will fit it nicely. What is the problem ?

This is fit nicely when loss the screw.


After screw back will like this.

Actually is more open, hard to shot that view.

1 more pic


This post has been edited by vincent09: Jun 3 2007, 10:28 PM

I try describe XD. Ok the first picture is loss screw and tidy fit ( look at the "3" line near that 2 "dot"
Then the 2nd and 3rd is screw tight and the "3" line there will pop abit out.

I just loss screw for the upper right ( the 1 screw of the real fan) then will tidy the line. if screw tight then will pop up..

I try align that case fan again ... XD.

This post has been edited by vincent09: Jun 4 2007, 12:40 AM

Hmm i'm not sure when i buy is already like that or i screw no so nice for that fan, the real fan still same is Lian Li's Fan. Ya now i did like mADmAn said, loose the screw but also tight and stable for the fan.

Yeah doom remember show picture again XD....
Actually how many LL case u have, always c you get new and sold old or keep.

Yeah, finally i can put that PSU air duct ( for psu heat to other place ). Last time i put, the PSU switch block, now cut off abit can put XD. Now still testing is it got help. Happy~

Normally the side fan that for exhaust GC card is quite near the GC because it easy exhaust out the hot air directly, for the big side fan maybe u can do for intake let more fresh air go in.



This post has been edited by vincent09: Jun 10 2007, 02:07 AM

O.o I interest on that filter if got XD......
Is it that filter can wash or just cleaning with brush ???

Let's call ATE get stock for that fan XD. If got sure take 2 XD.

sniper69 waiting for you message about that fan filter XD.....
Hope can apply on my case also XD...

Doom as you say if LittleGhost add longer extended cable for the case fan, so how to manage the cable for the real fan? Pull it until base the like those USB cable ?

Thank doom, i try for that next time when i change the fan.
You got any pic for make that kind fan cable management? Maybe easy to do with it.

Em, is it Lian Li case, the black metal that cover infront case fan will make noisy 1? That metal like filter.

I see, Doom you also take out that black metal web. Don't know y Lian Li case still put that at infront intake fan, the casing already got hole and savety there, now add 1 more metal web and block alot ... T-T.