Yes, ryudox's right...
The fan are too damn far from the radiator...

That fan doesn't seem like it's strong enough to reach the radiator...

[I just found out that this, is my 1000th post... And i just got myself 6 star!!! ]

This post has been edited by sHawTY: Sep 30 2006, 11:41 PM

i knew it..huhu. by the way,i also want to design my own waterblock..hope so.. congratz sHawTY..twinkle2 little starz...hehe

erm... must have been a while since i have been thru this thread...

anyways,

Now / currently i am running on Nirox P2800 , El cheapo pump. Not Bad. ( noise erm... i dunt think there is ) , Heat ( a bit warm ) a small 80mm / 60mm fan would do the job.

In My Case, The Pump is inside my casing so i have the case fan to cool down the pump's heat. been using it for a while


Before this i used a a really cheap aquarium pump, submerged it in a cookie jar and made some connector on top. the only problem to that was the heat dumped into the water. If u can get a bigger jar + better radiator, i guess the heat dumped by the pump would not be a problem.

Hope That Helps.

As For Radiator.

Try scavenging for a DAIHATSU MIRA / CHARADE Heatercore.

This 2 stuffs would do the trick.



gOod LuCK

Hey zahri, mind sharing with us your watercooling setup??

Janganlah macam tu bro shawty,

Malulah I .... huahuahuahua ...

erm... lets see...

New Pics taken, but not as a whole.


The Watercooling Kit.





Thats about the only pics i have currently...

The Watercooling Setup.

Nirox P2800
Daihatsu Mira Heatercore
Swiftech Northbridge Waterblock
DangerDen TDX Cpu Waterblock
1/2 inch Tubings, + T-Line + Swiftech HydrX
Shah81 Pump Relay

This post has been edited by zahri: Oct 4 2006, 02:24 PM

i did tried nirox p2800 and a used car heatercore for my earlier watercooling project. but i found nirox pump going to heat up after some time, i feel quite hot when i touch on the pump. so it gives a feel that the pump really dump a lot of heat inside the loop.

below is the picture of heatercore from used car and just did minor mod on the inlet/outlet fittings.

hollowbean,

The heatercore was taken from what car ? Nice...


sweet. i just found the pics of the el cheapo aquarium pump (submerged), this was my first Watercooling Setup.



This post has been edited by zahri: Oct 4 2006, 04:05 PM

zahri

if im not wrong its from toyota camry. not really sure, cuz a fren found that for me from half cut junk yard.

and how much it cost for that daihatsu heatercore?

This post has been edited by hollowbean: Oct 4 2006, 02:47 PM

sweet, no wonder its big

ERm..

The Daihatsu Charade / Mira Heatercore was salvaged from my friends workshop, its left behind from a few car converison, So i took it and went for Yamcha with him !!! Settled.

hehehe....

what ur price tag on the camry heatercore ?

It's free too...

car junkyard?

Preferable to Half-Cut shops...

yeah half cut shops

Junkyard shop also can ... hahaha...

my WC is using car heatercore and submerge aquarium pump. so far the performance is ok
running for 24/7
no problem yet

you mind posting up some pics for us?? pls do so

Here's my WC setup. most of the parts are cap ayam brand and second hand stuff.

The whole setup pic.


Only the tube (cap ayam brand) and WB inside the casing


Wats inside my external WC box


Water pump: Cap ayam brand
Radiator: 2nd car Heator COre
tubing:cap ayam tubing
Reservoir: biscuit container
Fan shroud: old Aluminium cake mould
Fan 12 cm size: panaflo(push) n vantec(pull)
Water block: Swiftech WB 2nd hand

Hey "epul"

That's a nice DIY watercooling setup you did there...

What's the full cost of em?

TQ

okay
aquarium pump - Rm 40.00
biscuit jar = 5.00
2nd car heater core = 45.00
Aluminium 1st aid kid box = 28.00
2ND Swiftech WB = 150.00
2ND PANAFLO FAN 12 cm = 30.00
vantec fan 12 cm = 35.00
Fitting = 100.00

These the thing i still remember

This post has been edited by epul: Oct 13 2006, 09:44 PM

wah... DIY also cost you RM400++ ah... wats the spec of your rig before WC and after WC ler??

theres some minor cost i didnt put n remember
but at my place the fitting quite expensive

well b4 apply this water cooling
idle temp= 53c
Load temp=60c n up

after apply
idle temp=42-43c
load temp=50c

but i doubt my temp software detector
but at least there some drop of temp
my temp cant drop around 30++
maybe to some factor

1.software detector problem
2. pump not power enough n also submerge
3.heatercore made from aluminium. if copper there might some drop of temp more