FYI, the venice E6 is the first to have SSE3 support.

hmm...how come it is so unfair, last time when i posted my spec and ask for OC advice, the mod ask me to post in the Q&A session, and close the thread. Then how come now can posted and ask for advice again? I posted in Q&A session also no one respond to it.

Anyhow, just share some experience with you. I m using Kingston ValueRam also can it can hit fsb 400 on my T-bred 2600+ (default FSB is only 266) by applying 2.7Vdimm. Running stable and passed 3DMark, PCMark, Prime95 tests.

hrmmm..ok. You mean retain my overall speed to like 1.8g and increase the HTT while maintaining the multi? ok

Juice is more than enough. i think more than 2.8 for a KVR is overkill. will try it out after CNY. didnt bring my pc back to hometown

hi,
i'm also new to OC. check out my OC'ed ram timing. from 166mhz to 222mhz with even tighter timing...

btw, my cpu temp after an hour of prime95 is 62C . idle is 42C. need a new HSF?
thinkin of acquire one zalman fan but afraid it wont fit into my casing

Pros, pls help me here. I got a64 eng sample & 2 stick of cheapo apacer 512M ram. One of the stick is pc2700 and another is pc3200.
Here's the pic from cpuz:

I can't get the ram run in dual channel (mobo beep)
If i wanna get my proc running in 2.4ghz, do i just set the multiplier to 12 (up the voltage if required) without applying the mem divider coz i leave HTT @200?

got question here, what if we overclocking our rig using 5:6 ratio(166Mhz) for RAMs & run at 270HTT, for sure in cpu-z, memory tab will show the frequency of RAMs at 225Mhz. my question :-

1. is the 225Mhz equivalent to DDR450??
2. if yes, izzit means our RAMs been 225Mhz(ddr450) & running at the current overclocked cpu speed example 2.7Ghz were equivalent to 2.0Ghz(default) running on ddr400 execpt bonus to the clock speed??

I am just wondering, is it possible to overclock an AMD64 3700+ S754?

I am currently using an Asus K8N-E, with 1 Corsair PC3200 CL2.5 and 1 Corsair PC3200 CL2. Board is running at DDR333. PSU is Enermax 460W FMA.

1. Is the CPU multiplier unlocked?
2. What does it mean by DDR333? What I know is it runs at the same cpu speed??
3. Even if its a minor overclock, can I say, overclock the ram, but with a lower   
    multiplier, achieving result of around 2.4ghz as well? Does that increase
    performance?
4. I might want to upgrade to 2GB memory, what kind of rams are good for an average
    OCer (I know this cpu cant o/c much), and what's the average price for these rams?
Thanks in advance, sorry for the noobish questions. Its been awhile since I've used AMD, and that was a 1.4ghz Tbird.

i'm super noob here...

my rig..

cant go more than 239 fsb..

239fsb setting....- mem 200 = 478mghz 3.3.3.7 @ 2.7v [corsair xms 3200 pro led]                    rev5.2
                        - HTT 4x
                        - proc ratio 8x
                        - proc vCore 1.492

240 setting - blank-bios blank...
                - so i raise vCore..still da same..

did i miss something

ok..i ve done it...

250fsb @ 250 mhz ram(500). timing 3.3.3.8 @ 2.8v

vcore 1.490..
but sumthing wierd. i set proc multiplier to 8x...@ bios...when boot up .to windows...n see @ CPU-z still 9X 

CnQ must be disabled if u plan on using a lower cpu multiplier, else it would go back to default whenever u enter windows esp if u had the A64 driver installed.

i'm hittin d wall w/ my ram too. sometimes lower dividers like 150, 140 wun work well (atleast in my case). no matter how loose d timin is i just can't get 'em prime stable... 

2/1.33??? lazy to do d maths... 

too lazy... 

1 q to ask u guys, if say memtest stable (dos ofcoz) but failed in prime within a minute, wat u guys will do usually... 

i'm havin hard time to prime-stable my ram @ 245MHz...