my pc spec is AMD 6000+ Asus M2N-E mushkin Ram 1GBX4 PC800 Zotac 8600GTS 320GB W.D muskin enhanced 550w psu Lian li Pc007FB. y i cant overclock until 3.2Ghz? n ram go to 4.4.4.12 ? but my fren pc lower then me can overclock better from me.... is it need to change cooling ?

my fren use same with my mobo but use 667ram 4GB can go to 4.4.4.12 o is it pc800 is very difficult to oc?

PC800     

DDR 266 = PC2700
DDR 400 = PC3200

DDR2 667 =PC5300/PC5400
DDR2 800 =PC6400

agreed wit u.. oledy seen some people oc using ta690g board..

hi all d dai kor here...
i'm using

amd x2 blackie 5000+
silverstone st56f
biostar ta690g
cm gemini S

i use d automatic oc in mobo...
sometimes will restart...
or when gaming...
it'll close d game itself...
if use normal clock...
dis problem won'r occurs...
can tell me wat's d problem...?

wat i nid to do if i wana oc to 3.0ghz...?

noob here...
ani program to test d stability...?

or ani setting...?

lower the HT link to 600/ x3 or 800/ x4

edit: ur  1GB+1GB+512MB DDR2 667 VALUE RAM ...is 512 is single channel ? and is single side chipset ?

better take out and use only dual channel 1gb + 1gb

No Option in BIOS to adjust multiplier for HTT . It just have basic Bios configuration.
And I think ram is the problem. Cannot adjust the voltage for ram manually. Hang

Info of my ram
1.   Kingston 1GHZ  800Mhz DDR2  Value ram
2.   Kingston 1GHZ  667Mhz DDR2  Value ram (Reconized in cpuz as Hyundai)
3.   Apacer   512MB 667Mhz DDR2 Value ram

is it all value ram is single channel? I've lack of info about ram .

Hi all sifus out thr. i have been readin overclockin threads for quite awhile now but stil dun exactly understand how to overclock safely.

N i am wonderin wat happens if i fail to overclock properly? does tat mean goodbye to my cpu or the whole pc ie mobo, ram, hdd etc. thx.

i am facing the same problem as you...
most of the guide i read is more on intel than amd...

hi all bro, sis, sifu, here.
im noob in OC.
already tried OC my PC. but facing problem.

details:
AMD 64 3000+ venice w/ stock cooler
DFI infinity NF4 SLI
2GB Kingston DDR 400 Value
Corsair 750w RAM
Cosmos 1000 casing

my tries is stated below. all stress prime test done for approx. 6 hours.

1. set HT to 3x, multiplier 9x and lower RAM to 133Mhz & 1.35v. Up the FSB until 250 Mhz & run stress prime 2004, pass. after that upped the FSB to 255 Mhz can't pass the stress prime. PC hang.

2. lower the multiplier to 8.5x all other settings same, can reach max 260 Mhz FSB. stress prime pass.

3. lower the multiplier to 8x all other settings same, can reach max 270Mhz FSB. stress prime pass.

all of these setiings gave me only 2.2Ghz only. i saw others can get up to 2.5 Ghz or 2.6 Ghz. Where did i do wrong?
scare to increase the voltage since i only use stock cooler. but tried to increase until 1.45v can reach 255Mhz FSB x 9 only.

all the temperature checked using core temp and stay around 40-42 celcius.

need help from all the OC master in LYN here.
thanks!

what is SS?   
to what level of vcore i can increase?
is 1.5v still considered ok?
i hope can get around 300Mhz FSB x 9 with 1:1 RAM or at least 5/6 divider.
Hopefully the RAM will "survive". 
Hard to find good DDR 400 RAM nowadays.
Thanks

hmm.. so thats wat vdroop is.. tq.. in my case the voltage is always the same when idle or under load.. when i set 1.4v it shows 1.376v.. for the temperature.. the different is not much when idle (2-3 degrees) but when i ran stress test the different become bigger.. im worried coz temp on core#0 might reach 60C while core#1 only 48-50C which i think is safe.. i look at bios and the temperature never exceed 47C.. so now im confuse which one to look at  yes at 3ghz its stable as i already run orthos for 12hrs with no error.. i dont hv core temp.. i'll download later..

i have few good one heheheeh pm me ekk

AMD64 6000+ +stock cooler
Biostar TF8200+
Crucial Ballistix Tracer ddr800/2GB

HI..im newbie here..can u guys guide me how to oc abit higher than 3.0ghz..?
thx in advance..

people dont want i take la hehehee