U can basically get it at any advertisement shop. Klang got 1 near old burned Great Wall/ klang bus stand. There got 1 gym for muscle builder. Just that row of shop. They also do car plates.

---

Added on February 24, 2008, 8:57 pmBrasso liquid form or Autosol paste form.

This post has been edited by N's: Feb 24 2008, 09:12 PM

umm pros i got a question, i have an angle grinder lying around and im wondering if i can use it to cut acrylic and to make a rounded edge as in nt a 90degree corners?

Grinder is to hardcore to cut acrylic. Dremel is okay. A simple file will do for round corners.

1 slip up ur acrylic = gone case

so u mean to say angle grinder can be used zit? how abt those plastic cutters can use also ah? thn the file to do the round corner is the kelikir rite? sorry i dunno wat iszit called in english

---

Added on February 25, 2008, 8:41 pmand pros 1 more thing i wanna ask the holesaw ah is attached to a normal drill or to dremel?

This post has been edited by someone_stupid: Feb 25 2008, 08:41 PM

It's vry hard 2 cut acrylic usin' angle grinder; it's a high-power tool more for grinding metals. Wht more u might damage the acrylic way more easily.

Plastic Cutter recommended more for straight cuts. File is aka kikir

Holesaw is used w/ power drill, not rotary tool

oh so the dremel can be used to to make round edges only zit? and not neccesary to use it to cut la ohhhh

W/ a rotary tool can cut any shape but for straight lines better 2 use Plastic Cutter (unless acrylic vry thick). Jst few drags & snap.

Cutting w/ rotary tool 'll produce more dust

ok.. this is a really noob question here.. i wonder, can power tool use for cutting? and can dremel use for drill hole? cos i see every tutorial on making a blowhole always using dremel to cut and then use power tool to drill..

Guess u r referring 2 power drill & comparing it to rotary tool.

A power drill can only b used to drill holes but as large as 13mm (or 10mm in lower-end models) diameter which is more than sufficient for all general drilling works especially in modding

A rotary tool, on the other hand, lets u do various tasks like cutting , polishing & drilling too albeit limited to 3mm diameter

If jst gonna do 1-time modding, I'd recommend getting a rotary tool & use diamond points to enlarge holes. After all most often the largest diameter u need is 5mm

thanks a lot

hi guys.. wanna ask some noob questions.. i'm thinking of repaint my CM elite 330.. but i dun seems to find anyway of dismantling the whole case apart.. pls guide me through..

secondly, do i need any special tools to scrub off existing paint before painting? any coating needed before spraying the new colour?

thanks

1.)u need drill, manual drill or a screw driver.. better drill dont go with my way(using screw driver)
to drill the rivet out.
2.)screw driver to un-screw the screw
3.)ask people who have same casing as urs..

for paint, look at 1st thread, then try search for paint tutorial or u could use tutorial that available in here

good luck.


This post has been edited by m2n-e: Apr 5 2008, 03:21 PM

er.. after the drill the rivet out... wont it spoils it? how can i put it back then? hehe.. sorry har.. pure noob here

u only drill rivet, also u need spare rivet for rivetting it backand using riveter which u can get at local hardware shop. dont drill till ur casing oso affect ler... just dril the rivet.

After drilling out rivettes, can it be replaced with screw and nuts?

o.... then the tip of the drill must be the smallest o?

can use bolt n nut..but i still prefer rivet..coz hard to find small bolt to fix the hole.summo the rivet make the joint more tough

yes. the smallest is good enough.

ooo.. okok.. thanks a lot sifoo!!