Sleeving Help!, Dual wire connector
|
|
 Apr 7 2014, 01:48 PM, updated 12y ago
Show posts by this member only | Post
#1
|
 
Junior Member
532 posts Joined: Aug 2007   
|
Hi sifu sifu at here,
I have a concern about sleeving my PSU that full modular. I sleeve almost all the part but the last thing make it look ugly is the "Dual wire" connect to the pin on my 24 PIN / PCI-E socket. Sample of image if couldn't understand what I'm talking  Any guide or sample image of sleeved for this part? Couldn't find it or maybe I'm not sure what to Google.  Attached thumbnail(s) 
|
|
|
|
|
|
Apr 8 2014, 07:47 PM
Show posts by this member only | Post
#2
|
Senior Member
1,435 posts Joined: Apr 2011 From: Blank Space
|
Summoning irienaoki for helping...
|
|
|
Apr 11 2014, 02:57 PM
Show posts by this member only | Post
#3
|
Junior Member
242 posts Joined: Sep 2013 From: Kuala Lumpur Malaysia
|
Hi Bro,
what type of sleeving you use? heatshrnkless or with heatshrink? that one can be sleeved.  |
|
|
Apr 13 2014, 01:46 PM
Show posts by this member only | Post
#4
|
|
Junior Member
532 posts Joined: Aug 2007
|
I'm using it with heatshrink.
|
|
|
Apr 14 2014, 03:21 PM
Show posts by this member only | Post
#5
|
Senior Member
998 posts Joined: May 2009 From: Bangi & Kuala Terengganu
|
refer my picture below..try join the wire in the middle(need to solder)..not join them at the pin..refer my worklog HERE
 This post has been edited by usop8290: Apr 14 2014, 03:26 PM |
|
|
Apr 15 2014, 12:00 PM
Show posts by this member only | Post
#6
|
|
Junior Member
532 posts Joined: Aug 2007
|
QUOTE(usop8290 @ Apr 14 2014, 03:21 PM) refer my picture below..try join the wire in the middle(need to solder)..not join them at the pin..refer my worklog HERE Thanks bro for the info! It help a lot now!   |
|
|
|
|
|
Apr 21 2014, 05:16 PM
Show posts by this member only | Post
#7
|
Junior Member
19 posts Joined: Jan 2010
|
Nice job done~ Bravo~! Thanks for the info too...
   |
|
|
Apr 29 2014, 12:01 PM
Show posts by this member only | Post
#8
|
|
Junior Member
242 posts Joined: Sep 2013 From: Kuala Lumpur Malaysia
|
you can also sleeve it without soldering. just place the sleeves on each wire, before you put heatshrink, try to melt the end of the sleeves a bit so that it will have tight fit on the end then put the heatshrink. i cant find the picture of my sleeving works, will look for it and try to upload it here so you will have and idea.
|
|
|
Jun 1 2014, 12:23 AM
Show posts by this member only | Post
#9
|
Junior Member
196 posts Joined: Sep 2012 
|
twist the wire and put wiring tape..but your wire will shorter abit..
|
| Change to: |  0.0175sec
 1.08
 6 queries
 GZIP Disabled
Time is now: 24th December 2025 - 09:35 PM |
Quote