Here take mine. 5k

BLM gooding. Cheap and cheerful. Butt slightly taller, will look sexy also

Buddy!

Thanks buddy! How's your car? And ofcourse how are you?

Luckily not too expansive stuff

The car has been idled for too long, I also forgotten needed to repair before start driving it. It is my bad, otherwise could have salvage it.

Yeah. Sold the little red and changed to Gen2, then EG8. And during my EG8 was sick, I was suffering to find transport, and so happen the yard called me ask me tow my car away, only I realized I got a part car Shawie in storage. So yea, after salvaged the part car, and now I decided I like Shawie more than Gentut and EG8.

Eh... don't masta me lar. Shy la We all friend² mar

Eh... don't sifu me lar, Shy la We all friend² mar

Migrate to new thread? Or shall we remain here since already passed 125 pages long long time ago? And I didn't see new TS also?

Double posted...

This post has been edited by davidke20: Jun 11 2018, 08:55 AM

I actually plan to redo the list of owner on 1st page. Can't possibly update on previous owner anymore. I should have continue support la despite I sold car 4 years ago. Now like dying ady.

Will start a new thread when I get a hold on my PC during Raya.

I'm sorry for your loss. For the Shawie per say, I'm sorry I can't remember which year is yours. If it has no problem, what for selling? Some points that need to consider:

1. If pre 2008, check for spindle if it has been replaced with latest revision. If not, and if you have a budget of 700, get it changed before catastrophic happens.
2. If AMT, just be aware of your pump. Change oil on 20k km basis, and make sure ELF oil only. If got problem ady, might as well sell it.
3. If newer, basically no problem means no problem. The only regular maintenance are speed sensor, temperature sensor and change your regular oil and coolant on scheduled basis.

Lastly, if you can find someone who buy your Shawie above 3k, faster sell. If not, might as well keep it. Or if you wanna sell besi buruk, sell to me 500

Part ain't cheap, but many thing share platform with Plotong Gaga BLM. So if you buy spare part time, tell the sifu u want BLM instead of Shawie, you can get cheaper.

Speed sensor DIY? How? U mean repair the sensor? Or you mean buy and replace DIY?

Fuel pump is not cheap as far as I know.

This is nicest. Appreciate a video guide if you have time for that. Will be huge benefit for fellow AMT owner.

Mine still working. I will consult your advice when I need assistance on this next time. Thanks for sharing.

Not until you open up the brake hub.

Prak & pray, not consider retrofit. The recent price I got from last week

Spindle 65 x2
Bearing 48 x2
Brakehub 90 x2
Hub cap 8x2
Upah 150 + change engine oil + filter

Total after diskaun 550

Thanks buddy

Hmm... Refer atas, tukak carbon brush saje kan day setel?

Yesh. Plotong GaGa BLM. Full set. The only worry is, you need to find the bearing lock nut for both side and also the bearing holder pin. These items I weren't able to buy and has to cari from my magician. the last time I change full set close to 1000 no doubt, that's many years ago. I also didn't aware price has came down.

1 more thing, make sure yours is not ABS. I didn't know ABS version can't change to BLM, so now my Shawie think my belakang henbrek x lepas will have to find way to disable my ABS now.

This post has been edited by davidke20: Jun 14 2018, 07:09 PM

The spindle got no problem even original. The problem is, if the bearing not properly installed, man you got a big problem. The inner bearing is smaller than the other bearing which sits on the brake hub. Meaning if 1 side of the bearing wear off, the tayar will kang kang and start grinding the spindle. And hence the spindle become weaken and break.

The last time it happened to me and @nox , we all got the same symptoms of those damn bearings keep on breaking within very short time. It will not last even 5k let alone 50. Spindle already bengkok, whatever good bearing u put in, the bearing tapper will wear off and the roller will get grinded off very quickly. Technically yes no need to change UNTIL flywheel.

Pre 2008 model con9lan7firm by Plotong is weak spindle, bearing washer too thin and wrong grease used. What can I say, that's their first time came out with brand spanking new own designed chassis!