Bro ,
U got pm, pls check.

Tq

pm best price for satria 1.6MT

Bro,

u got pm, pls check....tq

hi, pls pm me for satria 4g13 year 1998 fuel injection model stepper motor..thanks

This post has been edited by ~mingwei~: May 12 2014, 08:55 AM

Bro U got PM...TQ

TQ very much... Buyer from indo/ cheras/ seri kembangan.
1.6-2units
1.5-1unit

This morning one more stepper motor sold.
For Waja engine transplant 4g93 GDI model.
TQVM for the support.

Hello, bump...

Please do not hesitate, just send me ur inquiry.

TQVM.

i have a 4g91 pm

Hi danneal,

u got pm for the 4g91 dohc stepper motor.

TQ

hey! pm me for 4G91 please and also why does my idler bounces from 1-2k rpm when the aircond isn't on and when it's switched on it's around 1.5-2k rpm.

And also after a cold start it reaches around 3k rpm.

This post has been edited by MatureZebra: Jul 5 2014, 02:24 AM

Hi,
idler bounces from 1-2k rpm when the aircond isn't on and when it's switched on it's around 1.5-2k rpm.
Suspect ur idle valve (stepper motor) is not working well as it should be.

After a cold start , engine warmed up it reaches around 3k rpm?. Once warmed up it should going down to operation idle as 800rpm~850rpm.
Also suspect idle valve issue.

However, u can try reset by unplug ur battery negative terminal. Than plug it back on after 2~3 mins.
Start the engine monitor the idle timing again.

U got pm.

TQ.

Bro,
Me father's car wira 4g15 auto carb,after starting it with a low rev dies off and only when i rev it high a few times in neutral , force the gear into D gear and floor it,only will the car not die.

Or when I'm on the road in D gear the car vibrates violently on full stop with the brakes on and in neutral it doesn't vibrate.Bro could u tell me if its a stepper motor problem and pm me the price +installation.

Hi bro,

Gd morning.
The stepper motor / iscv unit I m selling is for fuel injection car only.

Auto carb engine I not sure. Please check with my friend and u may call him to ask about the carb engine issue.
I will pm u his phone number.

TQ

hibro, mind xplain more on what iacv/iscv/stepper motor for, please? walked thru n saw iscv/stepper=same=solve ac issues.

currently 1) when cold start, 3k rpm den slowli drop.
2) engine on, others off, when holding power window up/down or on ac, rpm drop 1-2lvl (0.2-0.4k?)+slightly vibrate.

will ur product solve? driving h.city sx8, year1998.

tq2

Hi bro, morning.

Sorry current I only have the isc/ stepper motor for mitsubishi and proton models.

I think ur car is not having the isc issue.

U need to get the voltage stabilizer or ground wires as well.

So when u on any electrical load it won't drag much of ur car voltage and well it will maintain better than before.

Less voltage drop.

Mostly is grounding issue.

Isc/stepper motor issue, it always will give u hard cold start, when on ac the rpm will drop low below the operations rpm level. Or engine stall when u on ac. Cos the isc / stepper motor is not working.

TQ

Thanks boss

but whn rpm drop due to ac/holdin power window, the engine sound macam going stall, while it'l fine when ac off/nt holding p.window.
it's grounding issues as well? =install grounding wire?

thanks again

This post has been edited by ttseongtt: Jul 10 2014, 11:45 AM

May be u can try ask the mechanic help u do the TB cleaning first. At the same time get the voltage stabilizer and grouding.

can try that first.

you may get the mech to check the isc to confirm the isc wtill working well or not.

Thank you boss, will get it for check 1st