as what they said, start delivery from mid July

here is my little review about the Crego slow juicer received week ago based on 1st time usage juicer 4 big and long stick Celery & Parsley.

Juicy efficiency
+ produce near half juice on juice collector
+ pulp is really dried
+ produce really dark green color juice (celery/parsley)
+ juicer comes with 2 assembly fliters/nets (tiny hole & bigger hole) i used the tiny for this round
- i encounter fibre stuck at the gear of assembly, not sure if i put too much of vege leaf at once

General
+ operating sound is quiet than centifugal type juicer; but still have sound la
+ the name call for slow juicer but i think it is not really slow haha

Juicer Installation
* first time installation I felt confuse but still manage to setup it

Cleaning Difficulty
- i will said pulp will remain inside from the pulp tube to the augar itself (pulp on augar i did not snap photo- pulp at augar is dried)
- so flush water while operating juicer is NOT sufficient to washing it (based on celery+pasrley)
- so i dismantle the whole assemblies and clean it piece by piece (they provided 2 brushes, 1 type likes tooth brush and 360 brush) tooth brush back side is useful to pull out the remaining pulp from pulp tube. 360 brush is good to brish tiny metal filter holes.
- because i juicy celery and parsley, their fibre is really stuck at those tiny holes and need to brush sometime to clean every holes, manual mentioned that it is not clean after use it will become stubborn stain. theoretically if tiny get block, i think juice will come out slowly...
- cleaning pulp from augar is simple once you dismantle it, flush water pulp will go away
- i think the most cleaning time is on the filter/net, over cleaning time 10-15min
- there are 2 silicon rubber from the assembly unit, red and grey. red rubber is easy to remove clean and put back. the grey rubber is very hard to put back, i spend 10min (time not included in cleaning time) to put back, and i realized actually no pulp sip into this rubber. i will not remove grey rubber in future. 1st time cleaning is too noob lol... i open everything!

I will said always dismantle and clean it, you will get familiar on the hardware installation and not fear/forget the steps.

What u see on the images are:
1. I already finished juicy, i flush water to clean it, not success; so those juice on collector is not real juice. at the same time u can see the pulp remain in the tube up to augar. you wont see pulp at augar unless you dismantle it. you also can see the quality of juice in the bottle.

2. on second image, you can see the red silicon rubber and grey silicon rubber as what i mentioned before in cleaning step.

This post has been edited by jimlim007: Jul 23 2017, 07:14 PM


Attached thumbnail(s)

may i know the strainer got 2 type, how to know which to use?

do you remove seeds before juicy for apple, orange, etc? pomegranate juicy with seed also no problem?

i believe it depend what you juicy, in my case is high fibre vege such parsley, celery. it depend how cleanness level you want, my case i want remove every tiny hole.

traditional juicer will have similar problem in cleaning on strainer, assembly, etc. but you talk about blender, by the design of blender is way simple there are no strainer, etc basically just blade and body. blender will not juicy for leaf vege... i am lazy to elaborate more.... continue what you like to blend.

thank you for sharing. i wish to juicy pomegranate, just worries the seed make juicer problem. that is rare fruit i seldom eat

it is depend what is your budget? everyone have different thought of good juicer vs budget.

initially slow juicer is extreme expensive, 1st come from Hurom >1500, then got other expensive brand too like kurving, primada, etc. all these branded.

then slowly after many years got so many copycat brand range from 400 to 1000. if you read thru this thread, you will find there are users bought expensive brand like kurving, cheap brand from lazada 4xx-5xx and also 7xx-8xx like crego, etc. crego is the last brand i hear.

i never have experience buy thing from lazada, i read review for slow juicer 4xx-5xx from lazada buyer, most of them are negative, some even said the received unit juicer is kind of used item, got pulp left inside. performance wise kind like little bit below moderate.

then i checked crego, i like few things like ship to my door, if warranty collect from my door (stated in their website), yet in their facebook review is >90% are very good review, spare part can get from their store, but problem is rm899 and i wait and wait, ngam ngam after 3 yrs i created this thread, when i have budget to buy, it give rm100 discount somemore, so offer price is rm799. to me i think this is consider good deal for such juicer. not sure about you....

before i made the choice on crego, i remembered i survey other brand like japanese brand price range 7xx-8xx, cannot remember is panasonic or toshiba, etc...