not sure how to steady more than that cos i fixed or lean my phone over rigid stuf already, almost like tripod, and place my phone on table, not held free hand like that.

share some pictures..

proshot, P mode, iso 100.

take macro shot,
but the phone must lean abit, like 45 degree angle..
if 90 no problem..

i think cos the OIS movement only X and Y axis only,

so, if lean abit, probably it dunno how to react and keep OIS-ing non stop.

ois in lumia i think is a basic two axis ois only.




if the gegaran is from top-bottom, and right-left only, it should manage it well. (| and <>)
the phone OIS can counter, cos it is designed for it,

but when the phone is slanted abit, ( / ) so the OIS mechanism not to say it totally fail la, but still not optimized,
it stil calculating or working very hard to keep the lens stabilizes until even during photons of light being captured by the phone.. so it means, the lens still in struggling motion when image is captured. only tiny movement tho..
so, theoretically the phone does not move, but the lens is moving rapidly that causes blur.

I have no problem with the OIS if phone is at ( | ) position.
Sometimes i do get super sharp image when at ( / ) position, but very rare lah.. must try banyak kali only can get..
I dunno how to reproduce, if not, i dont complain.. so it maybe depends on luck lah if i get sharp image.

looks ok to me..



lucky ah you..

ok too..
but quite bright la..
if no problem at darker ambient, then lucky u

after some heavy thinking last night,
i think problem is not ois..

perhaps my camera module not glued or the screw not tighten properly to the board..
then the larger clearance results in excessive ois movement..

so eventhough no movement or shake, the ois overdid the movement cos it can goyang on itself.. Got gap..


haihhhhh..

Make me want to open the phone and see it myself..

fuuu..

at 19:04 the camera is closed module..
and sure it need something on the body to holds on to..


as you can see, the camera module rattles when he ketuk,
so, basically the OIS movement of the camera happens inside the module, not outside,
not the whole module unit should not move,


when the camera module body itself is loosely attach to the chassis,
so it will kacau or add trouble to the ois mechanism on the inside

This post has been edited by thesun: May 28 2013, 06:54 PM

hmm.. maybe the gasket or rubber on the camera window on the outside doesnt press firmly the camera module,
perhaps it too thin or already penyek,
so the camera module able to goyang, which causes trouble to the OIS mechanism inside the camera module.


so, if i were to rectify this problem, maybe add some rubber ring on the camera window, so it presses the camera module firmly to the chassis.

This post has been edited by thesun: May 28 2013, 06:59 PM

why, scared issit? Hehe

ok la, so my phone faulty.

dang..

this is no competition dude.

proshot got updated.
now with exif display

also no more dual hand operation when using timelapse, burst, etc mode..

This post has been edited by thesun: May 29 2013, 09:52 AM

just select debit card,
insert card number, expiry date and 3 secret number behind the card, ur address,
select malaysia region at ur phone.

then u can buy..

925 over 920

dang..



i can see at least white balance is corrected, sharpness improved, and compression ratio slightly lower.

tadi tengahari, when lunch at mamak,
got one house nearby caught fire...

screenshot from video..
i dunwan share vid lah.. got many faces.,
and ppl crying, tak pakai baju..
helping to extinguish fire.



i did pusing and enter the house from infont,
fuarkk man...

2nd floor totally finish..
flames very big..


inb4 ppl talk abt pas flag.

This post has been edited by thesun: May 31 2013, 12:43 AM

yeayyyy!! i think i just fixed my blurr camera!

my theory is right!

yaaahoooo!