a liltle update on the project

replace the small panel with full cover panel







This post has been edited by irienaoki: Jan 6 2013, 11:34 AM

cardboards temp panel templates.









some of the acrylic panels.







fitting test



]





This post has been edited by irienaoki: Jan 6 2013, 11:34 AM

the hdd bay







need to make separate floor for it since need to lift up it few cm more from the radiator else the 90 degree will block the hdd floor.





This post has been edited by irienaoki: Jan 6 2013, 11:35 AM

temporary workspace
luckily after 4 months not using the mobo and proc still working great.
GPUs status unknown.
running on raystorm's D5 pump + bay res and ex240 (mobo only).
Quite good.







This post has been edited by irienaoki: Jan 6 2013, 11:38 AM

after 4 months of laying down on floors and staying inside the locker it s time to test the hardwares condition.











This post has been edited by irienaoki: Jan 6 2013, 11:38 AM

Rad dok atas katil?mewah laaa... tuan rad kena tido lantai..

more poison pls

this thread left dead since few parts still pending especially bitspower fitting and accessories.

this the parts that was confirmed by them (APES) but subject to change:

-XSPC AX 480 Quad Rad (black) x 1 unit.
-Phobya Nano-G 120mm PWM 1500rpm RED LED x 10 (or any red fins + black frame fans or combination with white and black fans –F12 & etc*.)
-Clear Tube 5 feets (Master Kleer) - ID 1/2" OD 3/4"
-Clear tube 1 feet (Master Kleer) – ID 1/2” OD 3/8
-XSPC M20x1.5 g1/4" adapter x 2 unit
-plastic clamp (black) x 10 units.

-Bitspower 90 degree rotatory adapter x 7 units (silver shiny).
-Bitspower 45 degree rotatory adapter x 2 units (silver shiny).
-Bitspower compression fitting ID 1/2” OD 3/8 x 2 units (silver shiny).
-Bitspower barb fitting 1/2” x 4 units (silver shiny).
-Bitspower fill port/pass-thru x 3 units (silver shiny).
-Bitspower stop fitting/caps x 4 units (silver shiny).
-Bitspower extender x 9 units (silver shiny).
-Bitspower Crystal link x 1 set
-Bitspower fitting for crystal link x 2 units (silver shiny).



This post has been edited by irienaoki: Nov 6 2012, 11:25 PM

waiting for the debut of blood red mayhem...picture please

thanks for mentioning it LOL

its all over your FB page LOL

it s not under sponsorship.
it s just a complimentary units from Mayhem.

for sure this take a long period to finish it.

few stuff came inside one big box.
salvage parts from old time.




fixed the acrylic with screws and aluminum mounts.





This post has been edited by irienaoki: Jan 6 2013, 11:39 AM

we want more

im in KL to pick some water cooling stuff from APES. will update once i back to east coast.

collected 80% of the sponsored parts from APES wangsa maju last week
here are some pictures of it.

XSPC AX480 Black















Bitfenix Spectre Fans and Bitspower fitting accessories



img]http://sphotos-e.ak.fbcdn.net/hphotos-ak-ash4/389424_10200206609391844_642583045_n.jpg[/img]




This post has been edited by irienaoki: Jan 6 2013, 11:40 AM

part of the collections







This post has been edited by irienaoki: Jan 6 2013, 11:41 AM

This post has been edited by irienaoki: Jan 6 2013, 11:41 AM

a little updates after 'hibernating' for quite a long time.

done on the acrylic panel for the whole case.
it s dual layer acrylic for each panel consist of 3mm+1.5mm and 3mm+3mm.




test the fittings on it everything looks good




AX480 quad rad will be located on the botton of the case for the GPUs loop.




Drive bay can fit up to 5 pieces of 3.25 hdd.




bay res 'intermission', direct to the top radiators swiftech mcr420 (thinking of replacing it with ax480 too).
dual bay res for dual ddc.







pass through with compression fittings on top and barb fittings below directly from ax480 rad.





This post has been edited by irienaoki: Jan 6 2013, 11:43 AM

time to improve the cables management for the case
since the clearance in between the side panel and board tray is so small this is the last resort for me.
P clips.








pass thru hole for 24pins mobo and 4 x 6pins pcie.
will be using extender for easy plug and play.






Terminal block for power split for the fans, LEDs and pumps.




naked chassis
damn that ax480 looks so damn sexxay.
thanks APES.
request for RX series. instead of RX480 they gave me the AX series.





fan for the drives bay.



This post has been edited by irienaoki: Jan 6 2013, 11:44 AM