Hey guys.. Tempted to mod my case but I can't seem to get any ideas ._. If you had this case, how would you mod it?

First, you can start with the colour if you dont like the current 1..

as usual, acrylic, BTX, bling bling, tyre R sticker.........

Sorry I'm new to this.. May i know what's BTX and type R sticker? Is type R sticker a sticker with the words "Type R"?

Yeah bling bling maybe but I wont do much, maybe LED exhaust fan only..

---

Added on December 8, 2011, 8:01 pmLooking for nice colour to replace Maybe change the silver to white..

This post has been edited by BenSow: Dec 8 2011, 08:01 PM

red will look good
make a windowed side panel with transparent acrylic

There's a choice of red for this case, but for some reason it looks awful for me


I dunno wether to go with acrylic window or mesh...

oh definitely acrylic windows man... no need for fans at the side panel imho.. cutting an exhaust blowhole at the top would be nicer

Okay acrylic windows.. Hmm.. Thinking wether or not it's possible to make the front panel "meshy"...

Yeah I might just do that but scared the cables block since PSU is at the top.. BTW is there any other source of electricity I can opt for fans? My mobo doesnt support many fans :/

This post has been edited by BenSow: Dec 9 2011, 02:35 AM

molex to 3pin converter

nowaday is hard to find mesh things..............

One molex can convert to how many 3 pins?

Why? ><

I DIY'ed a molex to 4 x 3 pin without problems but I cut an reattache the wires instead of crimping them onto the molex so it doesn't look as nice

Ok... Where can I buy connectors? Sorry but I dunno many threads selling case modding supplies >< BTW Should I be worried about the 12V rail thingy? I don't get that at all..

now thats something new to me, never bought them before... I just get from all my fan purchases

Then mind teaching how to DIY? I dunno all the wires wires thingy ._.
*EDIT* Nevermind I found where to buy but then I dont mind learning

BTW can I do the stealth drive thing?

---

Added on December 9, 2011, 11:32 pmOk now got some "kick" already Where can I custom order stickers and get proc stickers? And then is it possible to get this kind of plate?
Rounded edge also can.. And also custom metal plate engraving.. Where can I get this service? Thanks :DDD

This post has been edited by BenSow: Dec 9 2011, 11:32 PM

well molexes are quite simple really, depends on the fan, most will run on 7v and 12v and u can connect them via 2 wires (3rd is a speed sensor). the diagram below will give u a clearer idea

Ok thanks starting to feel this thread is dead already lol..

Hmmm.. If run on 12v isn't it sufficient for only one fan? o.o Sorry I suck at this

And I read somewhere that if we use 2 molex from the same cable for one 6 pin PCIE it will stress the PSU alot since drain from a single rail.. Apply to fans also?

I'm powering 4 fans off from the single 4-pin molex everything is working fine.. fans don't take up a lot of wattahe.. 6-pin pcie power is 75W output IINM and of course u plug them into GPU which normally would suck up lotsa power if its using dual 6pin

follow this step..
1. change colour.flat powder black and some red ati or green nvidia, depend on your rig sutup.
2. cut 12cm hole at top case.
3. cut side hole and put 20cm fan.
4. cooling setup.
a. water cooling for gpu, cpu or both.
b. air coling. make sure use masive cooling like cm v10 for cpu and the gpu use thermaltake or powerfull cooler.
5. buy fan speed control.
6. put fan many this case can take..more its better.
7. lighting. use ccfl ,neon or led. put sound retreck for extra cool
8. powerfull rig