Yesterday i also looking at low yat..... still no stock.......

to all sifus i am doing open wrt flashing for my mr3420. Here is the problem i tried to update the update list but it shows bad address. As per first post if the update link failed i change it over to on the first line.

#src/gz attitude_adjustment http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages
src/gz attitude_adjustment http://downloads.openwrt.org/attitude_adju...eneric/packages

Please help sifu sifu   



Holy cow now i click update list nothing appear..... not even bad address appear swt

What you guys need to do are:-

1. Connect 3G modem directly to your computer
   
2. Connect computer to TP Link router using network cable. On TP Link connect the cable to LAN port, not WAN port
   
3. Enabled Internet Connection Sharing (ICS) on the 3G adapter
   (Win 7: Control Panel\Network and Internet\Network and Sharing Center >> Change adapter settings. Then right-click the 3G adapter >> Properties >> Sharing >> "Allow other network users to connect through this computer's Internet connection". Under "Home networking connection", choose the ethernet/LAN port)
   
4. After ICS is enabled, the ethernet/LAN port will get IP address 192.168.137.1. What you need to do is add secondary IP address, e.g. 192.168.1.10
   (Win 7: Control Panel\Network and Internet\Network and Sharing Center >> Change adapter settings. Then right-click the 3G adapter >> Properties >> Networking >> "Internet Protocol Version 4 (TCP/IPv4)" >> Properties >> Advanced >> "IP address" >> "Add..." >> IP address: 192.168.1.10 & Subnet mask: 255.255.255.0)
   
5. Connect to router using Putty (SSH). Just enter IP adress 192.168.1.1 & click Open. It will ask you username & password. Username will be root & password that you set.
   
6. Enter this command (press enter after typing the command):-
   
   CODE
   route add default gw 192.168.1.10
   
   
7. Enter this command (press enter after typing the command):-
   
   CODE
   vi /etc/resolv.conf
   
   - Press "O" button on the keyboard
   - Type "nameserver 8.8.8.8" (without quotes)
   - Press "ESC" button on the keyboard
   - Press ":" & "w" & "q" buttons & press Enter button.
   
8. If you do this correctly, you should now be able to install the packages. Good luck!
   

Make sure u able to updates list, and install all the packages

◦comgt
◦kmod-usb2
◦kmod-usb-ohci
◦kmod-usb-uhci
◦kmod-usb-serial
◦kmod-usb-serial-option
◦kmod-usb-serial-wwan
◦kmod-usb-acm
◦luci-proto-3g
◦usb-modeswitch
◦usb-modeswitch-data
then reboot first before u try to set wan or other setting

well i dont hav any sierra, so i am not very sure,.

but u can try out if u want, flash it back to stock firmware if sierra not working 

---

Added on October 28, 2012, 12:55 pm

after all the packages installed,

just reboot the router

then loging 192.168.1.1

set the Wan,

the modem device will have usb1 or usb 0,

usb 1 will works for E372 and ZTE MF680 

yes it support E367 huawei

---

Added on October 28, 2012, 4:12 pm

dont have anyone in particular but a few selle rin garages sale who selling it,

depends on whethe ru want V1~V3 or V2 

---

Added on October 28, 2012, 4:13 pm

u have any other internet connection ?

or only this 3G connection  ?

using pc or laptop ? 

your pc have any wireless adapter ?