just tapao LC 5speed on the way to work just now..
he start with arrogant n loose at my 3rd gear+corner...
feels gooooood mang

Where did u tapau the new lc 5 speed???

---

Added on July 27, 2011, 8:59 amhttp://www.classictruckshop.com/garage/shopmathcfm1.php
Guys pls refer this 1....It's true ?The theory not block size minus half = to carb size ???

This post has been edited by 163119779: Jul 27 2011, 08:59 AM

sentul link...

not sure
but i remember Alex got mentioned before
it is minus half but dun ngam2 minus half

edit: and if kira betol2 LC de CC and the cutoff rev ...
it shows 22mm XD
it is quite accurate i think

haiz
22mm carb or 24mm carb more better?
round slide vs flat slide carb anyone heard of it round slide?

This post has been edited by Kaizzya: Jul 27 2011, 09:16 AM

slightly tune the rpm to 1.2k will be nice (Adjust the idling screw). Easy to start. Because ur timing very low.

---

Added on July 27, 2011, 9:26 amMostly carbs are round slide. Flat slide carbs is more expensive (Rare) unless u get the UMA mia. Is flat slide. Flat slide carbs mostly use in drag race and CUB prix and other racing purpose

This post has been edited by TryX: Jul 27 2011, 09:34 AM

ow..
thx for info =)
like tat TS125 is round de la

Yarp round one. U using ride it cam now?

dem.. my sprocket already got prob.. the chain is no more smooth pusing.. a;ready start membuai.. i cek the sprocket teeth.. still in good condition.. start use last month.. aiyo..

Motor sudah banyak penyakit d must find 1 specialist cure it d. Ur chain and sprocket newly bought?

yup.. last month i bought it.. do i need to cuci the rantai?

yupz..

membuai?
means?

@kai - how to say this.. usually if the chain still good.. when the bike move.. u can see the chain just rotate nicely.. what i means by membuai is.. that my chain is no rotate nicely anymore.. if double stand bike. and then let the rear tyre rotate.. u can see the chain is moving like wave.. and also the chain will produce some noise.. krek krek..

This post has been edited by budakmentah: Jul 27 2011, 10:32 AM

oversize a bit still better pickup and btw, due to wear and tear the piston get bigger bit by bit...haha

now using Keihin 28mm carb wit main jet 135 and pilot 35,block 57mm, FC getting almost 160km/h per tank d....

it still misfire but not tat often however until quite high RPM only will happen, i think this normal....

ow...

what chain u using and also what grade?
kenot go ketat liao ar ?

*like mine and aaron's current chain condition
but put some minyak and ketat abit
all ok liao(can tahan for a week i think)
and the sprocket haven't become shuriken yet
using SSS 415 de..

This post has been edited by Kaizzya: Jul 27 2011, 10:41 AM

boleh try cuci dgn minyak tanah. u got no choice also. if not ketat than kasi ketat sikit. Than lubricated with chain oil again see how.

@kai - im using 415 sss..

@tryx - o0o0.. last time i heard can also cuci using petrol / diesel.. can ar?

ow
lightweight chain
normal lo
becoz durability not so good compare to 420 and 428 ..
go wash it like tryx said and tight it back and lubricate it with oil

wd40 works fine also...

yup.. im planning this weekend wanna cuci rantai..
but dunno want to use what.. petrol? diesel? sabun cuci baju?

---

Added on July 27, 2011, 10:54 am@newguy - o0o0 wd40 just like the spray lubricant right? it is use for rust screw that cant open right?

This post has been edited by budakmentah: Jul 27 2011, 10:54 AM

what i did is spray with wd40, the previous if you use eo all will come out then wash your whole bike la....

it also can dissolve grease and EO, try la bro.... i think someone mention, not use petrol bcos any rubber might shrink...