INTEL OVERCLOCKING THREAD, TIPS,Q n A, Results...Great For NueBis
|
|
 Feb 8 2006, 07:20 PM
Return to original view | Post
#1
|
 
Junior Member
301 posts Joined: Jun 2005   
|
CTP d43 suit my p4 2.6c or not?
|
Quote|
|
|
|
|
Feb 9 2006, 10:01 PM
Return to original view | Post
#2
|
|
Junior Member
301 posts Joined: Jun 2005
|
Asus P4P800 se good for overclock or not with my p4 2.6c D1 step and CTP-D43?
|
|
|
Feb 19 2006, 02:41 PM
Return to original view | Post
#3
|
|
Junior Member
301 posts Joined: Jun 2005
|
D1 stepping 2.6c good?
|
|
|
Mar 28 2007, 04:45 PM
Return to original view | Post
#4
|
|
Junior Member
301 posts Joined: Jun 2005
|
increase the vmch is increase the voltage of the 965p chipset,but if increase the vfsb is for which chipset?
|
|
|
Mar 28 2007, 08:43 PM
Return to original view | Post
#5
|
|
Junior Member
301 posts Joined: Jun 2005
|
QUOTE(kevyeoh @ Mar 28 2007, 08:37 PM) blackthyra, care about your p965 chipset temperature,better put a fan on it thanks for the input bro...it's working now and i'm doing prime... i up my vmch and vfsb to +0.2 both and now i can hit 440Mhz... doing prime now... so now it's either choosing high CPU multiplier and get low ram speed... or lower CPU multiplier and increasing FSB + memory speed... any inputs?   |
|
|
Mar 28 2007, 10:48 PM
Return to original view | Post
#6
|
|
Junior Member
301 posts Joined: Jun 2005
|
QUOTE(BlackThyra87 @ Mar 28 2007, 10:33 PM) vMCH is the southbridge and vFSB is the Northbridge. oic,thanks  Added on March 29, 2007, 7:24 pmanybody know what software can see the real vcore?i set my vcore 1.325 in bios,but these 2 software shown 1.26 @@  This post has been edited by syapl: Mar 29 2007, 07:24 PM |
|
|
|
|
|
Mar 29 2007, 09:30 PM
Return to original view | Post
#7
|
|
Junior Member
301 posts Joined: Jun 2005
|
QUOTE(BlackThyra87 @ Mar 29 2007, 07:59 PM) i dont know why is it in ur case but for me, CPU-Z shown me the correct voltage at the processor.. same goes to everest 3.8 Ultimate... when my cpu full load,it shown 1.26v,when no load,1.28 v  |
|
|
Apr 12 2007, 12:28 AM
Return to original view | Post
#8
|
|
Junior Member
301 posts Joined: Jun 2005
|
QUOTE(AceCombat @ Apr 11 2007, 11:02 PM) so far i have no problem when oc with f9 bios of ds3 rev 3.3,i hit my Conroe E66 with 3.825GHz....using Big typhoon vx and idle at 28c........believe it?load at 57c,will not go more than 60c flash your bios back to F9?better?btw,anyone face the problem when install the vista on sata harddisk?the sata hardisk isnt run as Ide mode |
|
|
Apr 12 2007, 05:24 PM
Return to original view | Post
#9
|
|
Junior Member
301 posts Joined: Jun 2005
|
if enable the AHCI mode,then at the Onboard Sata/Ide Ctrl mode then choose AHCI,then harddisk will run as sata mode,then the NCQ function of harddisk will enable if your haddisk support it.otherwise if you choose Ide mode,then it will run as ide only
Attached thumbnail(s) 
|
|
|
Apr 26 2007, 08:37 PM
Return to original view | Post
#10
|
|
Junior Member
301 posts Joined: Jun 2005
|
QUOTE(Handsomeboy @ Apr 26 2007, 12:10 PM) I was using the Gigabyte 965P-DS3, but i can't Adjust the Ram timing in the Bios, so may i know how can i adjust the Timing, got any tools can make it??? ctrl+f1 in bios menu |
|
Topic ClosedOptions
|
| Change to: |  0.0458sec
 0.88
 7 queries
 GZIP Disabled
Time is now: 30th November 2025 - 03:21 PM |
All Rights Reserved © 2002- 2025 Vijandren Ramadass (~unite against racism~)
Powered by Invision Power Board © 2025 IPS, Inc.