juru SC also have r3 showroom..the rims also available there..quite heavy to me

berat tak berat, janji R3 Advanti. Hahahhahaha

Yeap, using Neo CPS rims for now. Transition mode before the R3 Rims. BTW, Neo CPS Rims have value on the market. Not rugi to pakai for a while. At least im not using the rim pasu bunga/rim besi.. hehehehe

*re-edit to show video*
Not really that heavy also.. But definitely heavier than most of the 16" rims on the market.
Janji drop-dead cun suudah...
aha.. Ya lah.. Marketing mah.. LOL.. Mine still the orange color wire.. Looks very outdated ady.. Ish.. 
Im not so good with welding stuffs like this all lah.. Now learning Arduino board programming from my friend.. So mb able to come up with some good ideas soon..
The tires look very small in relative to a big persona body lah..

U put a space in front of the number thats y it didnt show.

Ish waste time watching.. never go past 180kmh at all.. 
Then ask the SC to spray it back loh..

lol reached in the call after more than 13 times attempts... dang..... all the days already fully booked except for this coming Friday.... no choices.... and i asked them to put me the earliest bird to service my car lol.....

wow 180 max.... i only tried 170 km/h max only at karak highway before.... will try it again on DUKE after my 5 k services and of cuz DENSO.... hehhehe

Not sure the zapalang industry PLC or programing relay can do or not if cheap can try also...for the VS go eric page and cucuk him i see lot people ask for upgrade new unit VS now 160.00 ady....

COme waiting for u only.. My house very near MEX..  I need a slipstreaming partner to reach max speed of 260kmh..
nyek nyek is the door rubber.. Go buy a rubber conditioner and spray the rubber lining around ur door there..
balancing and alignment will give u drop in FC and increase performance lah..
Yeah but then those relay not so easy to find on the market and also they are mostly limited to 1/2 functions. The most i found also was a 5way different light pattern for only 5 connectors.. Arduino is 100% fully customisable.. And there is only 99connectors limit lah.. So practically anything also can be done.
Yeah the thicker the better, and also try to make the connecting points as short as possible too.. And also make sure its pure oxygen free copper. Some are copper alloy, so they mix aluminium in it too..
Spark plug + filter + GC + extractor only, total cost around RM750 and below for the best parts, but can get at least 11whp increase, almost eliminate throttle lag and improve gear change speed too.. Cheapest and best power mods for ur engine..

Hmm.. I can't see any R3 at cose. Dunno which part of cose at. I only saw lotus cars.
I think for beginning i'll use simple cheap board for the back light. arduino's price gonna kill me.

Got.. Lotus is at one side.. U go the Proton showroom there at COse.. Then go further in, all the way in... Got one corner there all display the R3 parts one.. U can ask the proton showroom staffs where is it too..

---

Added on March 28, 2011, 2:47 pm
Can lah.. Rm470 powerzone extractor +8whp, air filter 2-4whp, spark plugs 1-2whp..  Minimum also 11whp ady mah.. 
Powerzone dyno tested leh.. Only extractor alone. The rest all stock is +8whp. If add on with lightened crank pulley + extractor is +10.2whp.

Oh damn.. u are going to cry blood xandras.. I just found out..
Powerzone extractor only +8whp. Powerzone full set with 2 bullet, rear box and s-flow muffler They estimated is 13whp increase.
Hotbits dyno for full set, extractor to exhaust set. Dyno only increase 6.5whp. 

Erm their powerzone extractor alone on satria neo(no drop-in yet) dyno proven for +8whp increase.. But they didnt have a dyno result for the full set system at that time as they were optimising their setup..

Hot bits full set + drop in airfilter is 6.5whp..

Yeah apparently is cos of the design that they wanted the noise level to be under 78db as required by JPJ.. So there are 2 midbox.. Nono.. first they installed K&N filter +1.1whp. Then install full hotbits + 7.6whp, net hotbits gain 6.5whp.
Powerzone first installed mythelogy lcp +2.5whp, then installed powerzone extractor only +10.5whp, net powerzone extractor gain, +8whp.

So mai mai.. Lets bulk for powerzone now.. hehe..

Yeah apparently is cos of the design that they wanted the noise level to be under 78db as required by JPJ.. So there are 2 midbox.. Nono.. first they installed K&N filter +1.1whp. Then install full hotbits + 7.6whp, net hotbits gain 6.5whp.
Powerzone first installed mythelogy lcp +2.5whp, then installed powerzone extractor only +10.5whp, net powerzone extractor gain, +8whp.

So mai mai.. Lets bulk for powerzone now.. hehe..

Ur setup gain 12.5whp right? So lets say hotbits extractor +zhapalang exhaust 9whp, spark plugs 1.5whp, air filter 2whp..Total 12.5whp loh.. Makes perfect sense..

High flow also need to be fine tuned with piggyback also.. Suppose to be lah.. But i think their Knn is installed and dynoed on the spot.. Probably the engine hvnt fine tune the airflow yet.. If include S-flow shd be higher right? I think u shd go dyno again?    Dyno without A/F ratio only RM60..
U did dyno that time is using Works or OEM filter?

Ha Ha    flash on Myvi, get out from my f***ing way!!!