So, after I used the table saw to make my reference cuts, I grabbed the router with a 1/2" flush cut bit, set it at the appropriate depth and went to town. Making the reference cuts made the rest of this usually tedious job easy.







When I went to do the reference cuts on the shorter drawers, I realized... there were a bunch of screws in the way. Ooops! Good thing I noticed so quickly!



I had to go and remove all woodfiller and the screws that were in the way of the 3/16's inch material removal. This meant all the screws along the bottom, and 1 or 2 at the front and back of the drawer. What a pain!







After getting all of the extra material removed, I drilled some new counter-sink holes (Since the old ones were taken off with the router), re-inserted the screws, and gave all the dressers a light sanding, since I would have to redo the polyurethane coat anyways (They got pretty scratched up). In this pic, I had already re-stained the portion where I removed the extra material.



So. Next - polyurethaning the drawers... AGAIN!

fuhh what a long odyssey.....
but looking forward the final look....
all the best TS...

oh ahaha...
i finally saw that u hid ur keyboard n mouse there haha
good idea~
space savvy as well...
hehehehe

Thanks everyone - it sure is taking long eh? Almost done though!


While getting ready to re-polyurethane the drawers, I also took the time to stain and poly the right-hand cabinet door, as well as the two pieces that will be above each of the cubby holes on the top of the desk





Re-polyurethaning the drawers went really well - they look fantastic



Things have been pretty busy in the shop - have been re-glassing a war-horse of a canoe at the same time!



Here are the first couple drawers installed. They fit perfectly - the slides fit right into the grooves that I cut out. This photo turned out a little redder than reality



Getting the actual slides lined up and screwed in straight took a bit of patience, but well worth the effort



Ahh, nice and messy, but finally got the drawers in.



Some of the things I'll need to be working on shortly:

- Front Panel (Fan controls, LED's, Power/Reset switches, USB, Audio Jacks)
- Fan Installation (Foam surrounds, filter fitting)
- Hardware selection

After the hardware is selected and installed, I will be able to focus on cable routing and placement of the drives.

To TS: maybe u can add a small LCD display on the table to show ur computer state such as temperature and etc

omg a canoe! lol...

that's an awesome diy table to be

Ooh, that would be really sweet... we'll see about that as an upgrade in the future!

Haha, The Ultimate Computer Canoe is next lol!!

Sorry for the delay in updates everyone - I've been enjoying the beautiful summer weather we've been getting lately and haven't been putting a tremendous effort into getting the desk finished.

Surprise though - I did manage to get quite a bit done, and I've had some good fortune lately as well. I expect to post several updates this week, so just to get you back into the spirit of things, here's this weeks preview!

4x Scythe Ultra Kaze 120mm x 38mm 3000RPM
4x Scythe Slipstream 120mm x 25mm 1900RPM


Lots of foam cutting and trimming, and a sweet, sweet ruler from the Moddders Inc Featured Rig of the Month Contest(Thanks! I'm honored!)


Hmm, what's this?


Holy moly cool prize pack Modders Inc! I still can't believe I won this - perfect stuff for The Ultimate Computer Desk!


Finally removed the protective cover from these babies - they look soo nice!


Hmm? Another surprise?...


Oh good lord! What kind of super monster is that!!?


Bwahahaha


Ok, so maybe a lot's happened in the past couple weeks. I haven't been posting any updates because I've been tinkering around with hardware AND enjoying some good outdoor times. I'm thinking that the next round of updates in the following month or so will be ultra exciting - things are starting to wrap up!

Seeya soon!

After gluing a few blocks of foam together with a spray adhesive, I trimmed the block down to the appropriate size using a bandsaw.



Unfortunately, it wouldn't fit in order to do the vertical cut...



So I took out the trusty hand saw!





Here's the plan for the fan layout





At first I tried cutting the holes with a good quality knife, but the cuts were not very consistent and it took a long time. I ended up using an old drywall saw, which worked perfectly.



Test fit



Cut some more holes



Awesome!

Let's see how it looks in the right-hand cabinet



LOL - hilarious. It shouldn't fit like that. At least, it didn't during my initial measurements! I'll have to tweak that a bit later!

On to the crazy fans. I decided to go with 3 instead of 4. There just wasn't enough room for foam between each of the fans, and I figured there would be a lot of vibrational noise if they were touching. I could always go to 4 in the future if this proves to be insufficient.



Lookin good







Stay tuned! More stuff tomorrow!

I was in an extremely fortunate position recently. A friend of mine's work was moving from a large location to a much smaller location, and he had asked me if I wanted to come scope out the old office for any old bits of computer stuff that might be useful to me. To my shock and amazement, I was indeed able to pick up some pretty fancy hardware that I would have never dreamed of owning. They must have done some pretty big upgrades to leave stuff like this behind!

I was able to get a hold of a handful of Socket 775 motherboards with Core 2 Duo processors, a bunch of DDR RAM, a box full of Hard Drives, and some relatively decent (lower powered) power supplies. The real treasure though, was a pair of servers. You can see that I had already disassembled one of them:



2 Full 4U Antec Rackmount cases, each of them containing a Dual-Xeon motherboard + Processors. Both with FB-DIMM RAM sticks as well.

This particular one contained a pair of Xeon E5410's, with 16GB of DDR2 FB-DIMM's, 4 1TB Western Digital Blacks (SATA), and the motherboard is an Asus DSBF-DE.





The other one contained a pair of Xeon E5335's, with 4GB of DDR2 FB-DIMM's, 5 1TB Hitachi Deskstas (SATA), and the motherboard is an Asus DSGC-DW.

Now - before we go on - someone had queried earlier about the PCI Express slot on the board pictured, and I had said something along the lines of "Ya ya, it's there, don't worry about it". I of course, actually looked at the pictures, and no, it's not. It is indeed a PCI Express 16x slot, but on this particular motherboard, it only runs at PCI8. Now, the other motherboard, the Asus DSGC-DW DOES have a PCIX16 slot. When it was released, it did not support the 54xx series of Xeon processors, but I checked the website and there is a BIOS update to add this functionality. I will have to do a test setup with that board to update the BIOS, and then it will be swapped into the desk with a full video card, both the E5410's, as well as the 16GB of RAM, so keep that in mind when looking at the rest of this update. No, unfortunately, I didn't take any pictures of the other motherboard.

Cool stuff either way. Never, ever thought I'd have a dual processor motherboard. What an amazing find!

These dual Xeon heatsinks mount directly into the motherboard tray, so unfortunately, I couldn't use those spiffy motherboard trays from Danger Den. Also, since they are of size "SSI", there's no way it would mount on a regular ATX motherboard tray anyways. Time to drill out a tray!



It actually came out pretty nice and clean



This is a bit of a shame, since I took the time to clean the processors, put new thermal compound and remount everything. I'm just going to have to disassemble it again anyways when I put in the different motherboard. Ah well.

This is a bit of a hack job getting the tray mounted... Since the processors are mounted to the tray, I had mounted it outside of the desk, so when I went to fasten the tray to the desk, I was *gasp* actually lazy and didn't want to dismount the motherboard again... so umm.. I'm going to replace those odd-angled screws when I switch motherboards..



The power supply looks pretty good there. It's an Antec 650W - an Earthwatts maybe? I forget. I may consider replacing it with a unit that has a 120-140mm fan just to exhaust the air a bit better. The board has a requirement for a 24pin, an 8pin, as well as a 4pin, so I can't just use any power supply unfortunately.



The cables, of course, are not nearly long enough to reach the connectors on the board. I've already ordered the extensions and hopefully I'll get them at the beginning of next week. Oh, you'll see that I've straightened out the fans as well.



The cooling solution looks good. There will be two fans directly in front of the CPU's. I may consider putting an additional hole in the door to allow the CPU's and RAM to exhaust directly.



There is one major issue with the right-hand cabinet setup. The original specifications called for an ATX board, which is significantly smaller, so umm.. I have no idea where the hard-drives are going to fit. lol! Fun times.

Hope you're enjoying this flurry of updates. I may or may not be able to post an update tomorrow, as I'm going camping for the weekend! At the latest, I'll be posting again early next week!

A huge thanks goes out to Gigabyte for supplying me with this amazing motherboard - a GA-Z68XUD4-B3.

Without a doubt, the coolest motherboard I have ever owned!





I could barely wait to open this up when I got it in the mail!





And this poor motherboard tray that had been sitting for months and months covered in brown paper - finally had it removed. It looks even better than I could have hoped!



Here is the test fit in the actual desk



And with the fans in place



I'm going to trim off the plastic tabs from the motherboard tray to make it a bit easier to build the tunnels for cable management. Also, I'm considering putting a pair of holes beneath the motherboard to pass cables through underneath. Lots of stuff happening in the next few weeks!

I attempted to boot up the Asus DSGC-DW board (The one with the PCIx16 slot) but it would not boot. I'm afraid that that particular motherboard has gone bad, so I will continue to use the board with the PCIx8 slot. Anyone have any suggestions with regards to determining the best video card I can put in a PCIx16 slot with only x8 bandwidth? I was thinking I could look at the theoretical bandwith of an 8x slot and match it with that of the video card to maximize performance (ie. no point in installing a 5970x2 in an x8 slot).

Anyways, hopefully will have a handful of updates this week!

So - it's been another few busy weeks, so apologies for the no updates. Have been enjoying those last rays of sunshine before the summer ends!

I think I mentioned last update that I tried to boot up the Asus DSFC-DW board but had issues - here was the attempt:





I got a green LED to light up (Standby power on the motherboard) but jumping the Power ON pins had no reaction whatsoever. Tried it with a different videocard, re-seated the RAM and CPU's, but still no luck.

Moving onwards - since I un-mounted almost everything, I decided to keep the copper heatinks instead of the aluminum ones for the other motherboard. I also picked up a pair of these units from Rosewill via Newegg:





They should do nicely for my hard-drive racks. I would like to mount them like so, except higher up:



Unfortunately, they are deeper than the cabinet I built. At the time, I was thinking maybe they would stick out of my air intake window, and I would just build-out the section of the door with the air filter... Not exactly what I had in mind initially though.

With most of the major components in place, I decided to start tackling the cable management with some cardboard templates, and then some 1/8" plywood:







At this point I was a little frustrated with how slowly this portion of the project was going. Things weren't quite fitting the way I had planned, and they were not looking as nice as I would have liked them to...

Maybe it's time for some thinking instead of doing.

I decided (In hindsight, unfortunately) to go ahead and mount the hard-drive racks so I could get some better measurements and ideas of how to manage the cables nicely.





Installed the fans and started to route some of the cables



Took out a handful of old SATA cables... (Yes, let's not forget, that I'm a computer tech first, and a carpenter second, or maybe even fifth or tenth...)



And had fun connecting all the bits and trying to get them in a reasonable state of organization







Ugh... this will not do, this will not do at all. Might as well boot it up and see if everything works though (I had mounted and un-mounted the board several times, banged around a few things, etc, so might as well see if it's all still working!)

This would be the first time I see if all the fans work as well. Keep in mind that this is with the door removed.



Until next time.. still not quite sure what I'll be doing next.

Just a quick tips : if you wanted to enjoy longer summer , come to Malaysia (Promoting XD) , you get to enjoy hot sun at here.But now it's raining season so it's not the right time for you to come here right now.By the way how you get to know about this forum??

Hehe, I will have to come to Malaysia for sure some day! I have heard many great stories, actually! When I was in College, I made a good friend, and he was an international student from Malaysia. We shared some good computer stories and websites.

First off I want to give out a huge thank you to Seasonic, who has decided to sponsor The Ultimate Computer Desk by sending a ~really~ sweet Power Supply my way. An 850 Watt Seasonic Gold.




Thanks Seasonic! We'll take a closer look at that PSU a bit later..

I had been a little frustrated with the layout of the Dual CPU Xeon board for quite some time, so I finally made the decision to ditch it and setup the right-hand cabinet with an ATX sized board. This is more in spec with my initial design - the extra couple inches makes a big difference, and it will make it easier to upgrade in the future as well.

On one hand, I'm a little disappointed that I won't be using that super geeked out board, but rest assured, I'll find something else neat to do with it.

So I went ahead and removed everything and started from scratch. Looks way better already:





I then decided that, unfortunately, through the miracle of cable limitations, it would make a lot more sense if I put the optical drive in the front of the case, as opposed to up above the desk, where I had originally wanted to put it. So, time to do some more cutting.





The masking tape managed to pull off some of the polyurethane, but have no fear, I will be making a faceplate that will contain the power button, LED's, and USB ports that will cover that spot up quite nicely.



And, we've gone so far, yet, gained so little, eh? It'll get done, I swear!

I just noticed that you put the motherboard upside down...
LOL

your hand craft very nice

lol yes, well, if you think about it, there are almost no computer cases who have the opening on the right - they all have an opening on the left, so this was the only orientation I could use!

Thank you very much!

Feeling a bit more motivated about the right-hand cabinet, I decided that the foam fan-holder had to go. It was too large, was akward, and was difficult to keep straight and in the proper position.

I decided to put together a nice and clean fan holder:



After doing some measuring, I took it to the drill press for the initial holes (I didn't have a hole saw for 120mm fans unfortunately... that would be pretty huge!)





I then took out the spindle sander to sand right to the line. Just an fyi, I swapped out the spindle for a much larger one. This was my first time using this type of sander, and I was very impressed - the degree of accuracy and control is extremely high - perfect for sneaking up on the pre-drawn lines.



Time to drill some holes for the fan screws



And a test fit. The product came out quite nicely - accurate cuts, all 4 of the positions are secure with screws, and this piece should be much easier to align in the proper location in the case.





I had cut a few other new pieces for cable management, but they were rough cuts, as I will not know their exact dimensions until I install hardware. I can't install hardware until I finish cutting and drilling in the right-hand cabinet, and since there is still the issue of the power button, LED's, etc...

Time to get started on that, I suppose!



Kinda looks like a bull head eh?