Mine is.....
[attachmentid=1749841]

[attachmentid=1757268]

guys,this chip got temp sensor problem? i am running it under TRUEX 
core temperature never fall below 42'c

guys2 help me out. i got 2 proc here. dual core E2140 n c2d e6400. if i want to oc which is better? extremely noob asking extremely noob question 
my current system is
dual core e2140 1.6ghz + stock hsf
abit ip95 + kvr 1gb
hd3650 n cap ayam psu
had c2d e6400, nvidia gf 9600gt n gigabyte superb which is planning 4 a new system. n also want to oc kaw2 it. help me n give me recommendation plis2 

need help,how to oc to 2.6ghz++

spec:
c2d e6300 1.86ghz
2gb ddr2 667
2 hdd
1 dvd rom
ati 4670
stock cooler
cap ayam psu

341x7 is the highest it could go
using kingston value ram

above that cant enter windows

dram multiplier is system memory multiplier?

lowest dram multiplier is 2
if auto will set at 3

---

Added on September 3, 2010, 12:31 pmi try
370mhz x7
ddr2 overvoltage control +0.1 to 0.4v
fsb                                  0.1 -0.3v
cpu voltage                      1.3v-1.6v
can't enter windows<-----this suituation call CAN'T POST right?

Shall try when I do my next oc...

Ram is 1028. 1:1, can't go any lower.

i changed my FSB to 250 and my e4600 can run at 3.0Ghz.. but the problem is when i run prime95.. the temp will rise straight to 70.. how can i lower the temp?? HELP!!!

vcore at 1.392
cpu cooler CM TX3..
i doubt the casing airflow is not so good.. bcoz when i open the side panel.. the temp drop abit...
what should i do??

no.. it didn't.. BSODed.. im a really newbie in OC.. so u suggest i shud drop how much?? i set it to auto b4..

im using 2gb kingston ddr2 800 and leave the dram to auto.. wat shud i do??

i stop at one hour because the temp is at 70.. is that a prob??

Hi, tried to Overclock the E2180 but am stuck at 2.20. It works fine at this speed.

however, immediately after increase to 223 or 226 and exit BIOS, it will go silent for a while then automatically resets back to default 2.00 before POST. Hope any sifus can give some opinion:help:

My Specs and config in BIOS are below.

Intel E2180@2.20ghz
Gigabyte mobo: GA945-GCM-S2L Revision 1.00 F4
2Gb 667 -PC 5200 Kingston value ram 4-4-4-12
sapphire 4670 512 mb
1 TV card
Windows XP sp2
1 DVD drive LG
1 USB wireless TP-Link
1 AVF 450W PSU (Cap ayam)
1 PCI fan

memory frequency multifplier = 2.00
FSB = 220
CPU Multiplier = (cannot change in bios)
PCI Clock speed = 100
vDimm = auto
FSB overvoltage = auto
Vcore = 1.325
EIST = Disable
CE1 = Disable
Temp = 48 - 65 c

Thanks for all advice. smile.gif

Thanks for reply 
Tried to lower the multiplier for DRAM but lowest can go is 2.00. Memory Frequency 400mhz. But its still below 667mh right?
If set to auto.......would not even start. shoot up to 7++ mhz.
Maybe I can increase the timings?
probably my Mobo limitations? ..........Googled..........other people's best bet was 1:2.
I remember being successfully going to 2.23 or 2.26 once but can't replicate it again.

i need some help guys, here's my specs:

Gigabyte EP45-UD3P
E5400 2.7Ghz
2 x 2GB KVR RAM
GTX 460 1GB
CM RealPower 550W
CM V6-GT

FSB=333Mhz
RAM=800Mhz (No OC).

Initially i o/c-ed it to 4Ghz and it was running fine for a few months..., but recently, when it boots up, sometimes it'll lose the OC settings and
goes back to default.

I'm not sure how to set those settings in the voltage, so i just default it in the BIOS (which was working previously). The core voltage goes to 1.4v.

Whenever it lose the setting, and i return to the BIOS, a red warning message will pop up regarding some failed OC settings on previous run.

Could it be a mobo problem? The LAN port (2 ports!) just kong out recently...i think around the same time the problem appears...not really sure though....can OC too much knock out LAN ports???

Pls help!!

After bumping up the PCIe frequency and IOH/ICH PCIe voltages, I fried the onboard Intel gigabit Ethernet controller. It simply wouldn't show up in Windows afterward.