-5v ? i dun think it has anything t do wif stability. onli 3.3v n 12v is used. 3.3v for rams n 12v for hardware.

he mention -5v bro... the negative 5v rail

This post has been edited by satanhead2003: Feb 22 2006, 11:50 PM

Me second on that

After u flash the bios, list these here :

current Vcore w/temp reading
current Vdimm w/timing
current FSB
current multiplier
current divider

we'll help u squeeze out the last drop oc'ability of it...

1 - try lower multi n crank up the fsb.

2- when u raised fsb, raised vdimm 1 notch to 2.7 when it pass 200fsb.

3 - Let say, ur target is 2G, if u're able to get 2G, try to thighten the ram timing. try 2.5-4-4-8, prime for 30minutes but with priority level 9. if succeded, lower it again to 2.5-3-3-8, prime again. until u hit the wall for the ram.

try these timing :
current :
3-4-4-8

to test :
1st - 2.5-4-4-8
2nd- 2.5-3-3-8
3rd - 2.5-2-3-8
4th- 2.5-2-2-8

if u're able to get 2.5-2-2-8, try :
2-3-3-8
2-3-2-11

if u succeded, then :
2-2-2-11


have any enquiry or question.... u know where to find me....

a little "idola" for u :

try upping vdimm to 2.8 . see stable or not. if oso not stable, use 3-3-3-11 like M@STA K1LL4 said.

This post has been edited by satanhead2003: Mar 2 2006, 06:33 AM

@zahri....

what ur idle temp?

no prob..... just watch the temp.... never get it exceeded 70c. ur proc onli tahan until 80c. the diff will be :

higher clock wif some bandwidth gains. Gud luck dude..

D26 for 2T n Taipan D27 for 1T.

Try merlin D27 CPC ON latest ( watch the release date ), if not satisfied, try D26 Mantaray XT CPC ON.

There's an issue with 10 n 10.5 multi on nf2. try to avoid these multi if possible....

yeah..... with higher multi, onli get higher cpu clock. with higher fsb, will get higher bandwidth.

from my personal experience, this 10 n 10.5 multi bandwith is not consistent. it even bsod on me.

2.6v is not enough la dude..... try 2.8 or 2.9. KVR carry lifetime warranty... so dun worry.....

hehehe... aku plak .... 9 x 253@1T atau 9 x 260@2T. hehehehe
XP-M le...

You go for the xpert, dude. good choice.

Hahahah... same casing as mine...... but, well.... i've modded mine. throw away the shutter, potong the lower part n added JMC 12cm fan for hdd cooling, paint flat black for the interior, cut the back honeycomb blowhole, enlarge the sidepanel to 12cm fan....

be sure wat u're doing there, dude. once u flashed an unworkable bios.... hehehe.... say bye bye to ur mobo.

abt the fan.... i think, better use high cfm ( around 100 - 120 cfm ) with air-push config. but, the casing limitation is 8cm on rear. so it's better to get fan converter; 8cm -> 12cm. A high cfm fan will be loud, not from the fan, but the "whoosh"ing air that go through the rad fins. try to get a fan controller.

Well, this is my result with 1 stick kvr hynix bt-d43 using taipan d27



200 FSB 1:1 2-2-1-2 @2.9v

with Mantaray XT 2t, i could achieve 263 w/ same timing. sorry, lost my shot for 2T.

This post has been edited by satanhead2003: May 22 2006, 10:41 PM

i'm not in socket A anymore. migrated to sc754. but surely i hv so much fun with this stick. . combined w/ AXP-M ( bought from Dinster ), this stick does shows it's best. But to be honest, to achieve this, i had to burn-in for abt 100 hours. well, i guess, it worth it.