im the third person to post in this new thread even though i dont have WC setup.....yet....
want to ask sumting
i want to buy this item for my setup

1) swiftech apogee xt
2) swiftech mcr 220
3) ek 4.0 pump
4) ek multioption 250 res
5) Bitspower 1/2" 3/4" compression x 1 pair(silver shiny)
6) Bitspower 1/2" Silver Shiny barbs x 4 pairs (silver shiny)

izit good enough to cope with 4Ghz OC??

@metsatsu
nice setup bro...
how much it cost for WC only??

anybody know a good reservoir that can fit in the rv02? my reservoir is hanging by a single screw and 2 cable ties only 
Very scared it won't hold...
if ek multioption, where to put?

give me a god damn DSLR i'll show u my rig .
haha
anyway, its up to u whether u want to change the inlet/outlet thingy or not .
cause for me, even 1C brings different .
dat's how u compete .
u cant bring down 10C at once .
u gotta eliminate 1C by 1C .
hehe

to satisfy ur needs for proof .

[attachmentid=1685561] [attachmentid=1685562]

Juz wanna share with every1 joke of the day,

wah using distilled mineral water also can?

good idea 

but will it make the whole WC set corrosive?

should be ok la dude no worry about the temp .
mine also wander around 68C on linX 65c on prime95 .
running at 1.3v 4ghz ht off .

try to lower the voltage cause i think 4ghz doesnt really require more than 1.3v .

@clawhammer

noob or not shit does happen .
and better be safe then sorry .
anything can happen .
even a small tilt to the casing would cause the water to spill .

u all dont want to spend 5 sec of ur life closing the fill cap then up to u .
there's a reason y the word "precaution" exist

u want to talk about car ?
that's y those inventor created side mirror n rear view mirror and the PRECAUTION move is u LOOK at them when u wanna change lane .
not simply change cause it MIGHT cause accident !

not that it will confirmed cause accident .
but if it happens, then ur car burn and u die as well ?
u want that to happen ? be my guess then .

I don't think theres a problem to be safe.. I mean shiit does happen.

either way if u mean by constructive, you should actually politely saying that he is wrong. Saying noob or stuff isn't mature in my dictionary.

look at how much voltage you use, with that amount 70 is ok. my i7 pump in 1.275v loads at 65 celsius

From...


To...

According to to ek manual theres no difference between these top/ bottom holes as inlet/ outlet but wil try to swap them later hehe
Yes the bottom feser480 rad is in push pull fans setup but less 2 fans at the back coz been blocked by psu. Need slim fans only can fit. Anyway i m still curious why after adding athe top feser360 rad i got no improvent in terms of core temps. Pwm at 1.55v is 62c load which is quite bad since my table fan can do it at 68c. I smell sth is going wrong with my setup since the beginning. With or without gpu blocks is the same stil that high. confirm bubble free hmm... Wanna try other cpu block anyone got ek supreme HF ready pls pm me

---

Added on August 12, 2010, 12:07 pmParts are listed in my siggy guess ure using mobile phone to surf. My avatar is one of the recently bought items. Yup wil buy the D90 soon to replace the parkinson illed Ixus.

already tested that dual d5
didnt make much of a difference.

There is only 1 20 CM fan included. I mount the radiator at the top of the casing; thus, it can no longer fit the 20 CM fan. But I mount 2 12 CM fan on the radiator to blow away the heat dissipated at the radiator's fins.

Just set up my first WC system..bought from Bro Alvin

hehe waaaaaaaa lu all punya rig bayak cun lo
sy punya hehe murah set only.....

spamming here...   
Cable Management and added wheel to the case.