where can i get a non-corrosive additives?

ya going to mix with spritzer distilled water

any idea? where can get?

ok thanks bro will look for vlad

Cooler Master Aquagate Max (RM700+) price almost near to custom wc.. just add bout rm200+ and u will get very go custom wc..

try consult clawhammer and vladtheimpaler..... both of them got wc set ready to install....

This post has been edited by subrok007: Aug 19 2010, 06:42 PM

DzX bro,

how do u cabling all your fans mount on top of radiator outside?

i was so geram those wire.. dunno how to do it... help...

yes, compression fittings damn hard to loose it after we over tighten it..... advisable not to use playar to loose it will definitely scratch... use hand to twist compression fittings and another hand twist tubing

picture up soon... my WC setup

This post has been edited by subrok007: Aug 21 2010, 09:34 AM

later will up....

how bout ur picture ronaldjoe?

btw, guys can set the EK Multioption Rev2 Reservoir terbalik?

yes mine 1 is old 1... but i got bubble inside...

but then where u hide this??? since all panel close.. how did u route the cable?

thanks the tips....

thanks owikh84, i found the solution easy n save money for radiator fans cable connect..

so here spamming part....



guys, is it after shut down computer, the coolant will flow back to reservoir rite?

performance part



vcore in bios 1.375v... not really best performance yet... bcos tubing got a lot of bubbles.....

custom water cooling really best performance indeed, i tried b4 highend cooler Thermalrigh True 120 BE, Coolit Domino ALC, etc...

True able to withstand to 70+ full load 3.6Gz, while Domino ALC around nearest 70+- full load... not really good but

water cooling best ever.. of cos money also best ever...

as for problem part... i have dy solved it... will post new performance in later days.

This post has been edited by subrok007: Aug 28 2010, 10:45 AM

on and off many times still same... pump drain almost finish then coolant from rad just filled back to res causing air trap inside tubing to pump..

alan kc,

yes my inlet is from upside, outlet is downside...

supernothing,

bleedy loop is let the small bubbles out... but my problem is feel like reservoir capacity too small for my whole loop...

the problem is like that...

start pc, pump pull coolant frm res, coolant almost finish until u can see no coolant inside res, then baru coolant from inlet filled back to res... that's y i believe that happening causing air trap inside tubing.. am i rite??

haih... but my tubing not enough length liao...

and also make it more messy inside... try the tubing as short as possible...

any idea bro?? instead that

bro u mean both inlet and outlet must place at bottom rite?


yes, i scare it will overflow when i shut down my pc.. but is just ngam ngam if more abit sure overflow liao..

so u idea is start pc then filled coolant... let it running. then prepare drain tube for overflow after shut down??

yup... will try adding coolant again... see how's going...

leak test pass... no leak...

wah sambung paip very dangerous lo... will leak 1...

will looking clawhammer again for tubing part..

yes....

any1 tried b4 using swiftech reservoir with quad radiator?>



This post has been edited by subrok007: Aug 22 2010, 03:51 PM

yuanbao..

u using Swiftech MCRes and quad radiator? that small reservoir enough for quad radiator?

this is wat i thinking now... may be will change inlet position to bottom..

or ask clawhammer for solution.. any how still need to buy tube again.. money gone


how said so?? not really understand since this is my 1st custom wc..

oic... yes may be my radiator still got air inside... not fully filled..

but bro, u mean lay down casing (sleep pose)? then fill coolant then just pc on??

yes that was simple way..

hey where ur picture?

bro where u spamming (Pic)?

---

Added on August 22, 2010, 4:08 pmb4 that, how was my temperature? is it ok?

This post has been edited by subrok007: Aug 22 2010, 04:08 PM

yes, the problem i saw is when i start my pc.. the coolant drop very fast until finish then inlet baru fill the res...

ok ok will try it... jump start pc.. shaking and fill coolant again.. how bout if i stop will it overflow?

spam the setup without radiator ..

This post has been edited by subrok007: Aug 22 2010, 04:19 PM

off topic..

wah so syok student then part time seller processor...

sad, i just using elite 430 nia..

water block > radiator

if no gpu block.... cos theoretically, hot water must cool down by radiator.. not cool water again cool down by radiator.. even car design also like this.. engine > radiator.

rev>pump>wb>rad>rev ... this will be good idea for simple loop as my..

hahahaha... dont play play bro....

ok will try it... yes as i mentioned there dy... performance not 100% yet... cos got a lot bubbles inside... somemore now just realize my radiator not even full fill coolant.. really

your procedure is

lay down casing
fill water (vertically)
jump psu start
let it running

am i rite?