Corsair is better. CM has way too much plastic and they look ugly

V6GT uses CM Xtraflo. Which is the same fan as the Blademaster. It is only loud at max RPM. H100's fan is also freaking loud and it's quite normal. If you want high performance, high static pressure fans that are not loud (or acceptable at max speed) you can get either the Scythe Gentle Typhoon AP15 or Noctua

Yes they can be replaced. Nothing wrong with it but some people say they are VERY NOISY. They are the same fan used on the 212 Evo but the 212 EVO only comes with 1 piece. The fans are only noisy at full blast 2200 RPM, which is quite normal. The corsair H100 at 2k+ RPM is ridonculously noisy too.

Entry level corsair hydro series is not recommended, you get better performance with air cooling and they lasts forever. Once the Hxxx pump goes, you can throw your whole cooling solution away. For H series, one should only consider H80 and H100

Don't build that many CM but here's a HAF-X we just built















More pictures here: www.cyntrixtech.com

It's a reservoir + pump top combo.

It's an EK360. It's missing a fan and will be completely replaced by AC F12 PWM tomorrow. We have 80 pieces of them

Looks like a

Cosmos + 600T + 800D super hybrid. Those two handles look really ugly.

F12 PWM is much better/quieter. At RM30 it is hard to beat. Another contender is the CM Blade master which also has very high static pressure but it's a little noisier

You can get it polished but you are better off just ignoring it or have a new acrylic cut out from an advertisement shop

---

Added on December 29, 2011, 10:21 pmCooler Master Elite 311 Plus











This post has been edited by CyntrixTech: Dec 29 2011, 10:21 PM

Getting out of topic, now lets go back to:





Who can guess the complete spec?

Can you guess the complete spec though?

Some hint:

- Red Ram
- Our favorite single GPU PSU
- No hdd, some 80gb ssd

That's all! You should be able to compile the exact hardware spec

Cooler Master 692 Advanced Watercooled (XSPC RASA RX240 Kit)







Full album here:
http://www.facebook.com/media/set/?set=a.2...67942523&type=1



This post has been edited by CyntrixTech: Jan 12 2012, 09:59 PM

Without those 4 ugly things sticking out of the casing, I'd say it's a pretty decent casing by CM

I think we just claimed first watercooled Cosmos II in Malaysia

Cooler Master Cosmos II Super Tower - Watercooled






This post has been edited by CyntrixTech: Jan 19 2012, 12:32 AM

Cooler Master 690 II Advanced - Watercooled (UV Green)

We'd build a Green rig once we secure a unit of Gigabyte Sniper Btw very nice. The coolant almost look like mayhem dye

This post has been edited by CyntrixTech: Apr 10 2012, 12:05 AM

Can you take a picture of the side panel opened, front shot view, like those we usually take? It seems that you could route the FSP PSU cable behind the mobo, if that's the case, this casing may be made our favourite sub RM 1xx casing besides the Xigmatek Asgard Pro.

I hope you twisted the yellow fan sensor wire, it is the most annoying wire on the F12 PWM

You sure have paid great attention to how we route and hide all the cables

The quest to finding the best RM1xx casing hasn't ended.

Above is a Xigmatek Asgard Pro. Can't hide the 8pin mobo cable with this casing otherwise it is close to perfect

If you are going for Ivy Bridge, this cooler is no longer enough to handle the heatload.

IB generates a ton more heat than SB. We have about 3 pcs in the works now