that memory dump?
i think that is not ram issue..that is the countdown for a file (dump file?) to be written so afterward the problem can be analyzed or read..after reboot..

so far i remember, is the ram highly unstable, it hard to boot
if quite unstable, it will restart after 1 or 6mins of priming...

from psu only 2 wires connected..
if from mobo all 3 wires connected.. hence can control the speed..
unless u use chap ayam fan that connect using molex lol
if direct from PSU also can make it spin <100%...mod the wire to take from the 5v one..kekeke

This post has been edited by kuntawakaw: Jun 3 2010, 04:24 PM

cm bising..kekeke
slipstream go search clawhammer..but someone selling slightly cheaper..i just cant remmemeber who..

sorry..me wrong..
i dont think 4pin only can control..the speed control is just the volt right? even 2wire connected can control edi..just depends on the mobo support to fan adjustment or not..correct me if im wrong..

yeah..
agree..regor is super cool chip... on stock cooling i think 1.45v still ok..

y dont u try it ur self..kekeke..since i also might pick that proc for my bro..so later u share the max oc with me k?

if got money..no need to wait bro...
u buy...and change if bored...kekeke

btw hard to see ppl using asrock..i wish i have some money to spend..
iinm lingloong selling it...
i want to try this


btw fast2 recover verdict..
regarding ur previous post..i have no weapon now.. unemployed..wait nxt week to get some job 1st..

@ah_khoo
wait..u did tried same ram on 700series chipset right?
can tell the diff of new chipset in mem clocking?

edit: what ram cooling bro ?

This post has been edited by kuntawakaw: Jun 12 2010, 09:23 PM

@cloudwan
remember my crap setup?
now at 250HTT...kekeke


owh wai..y shud i end up with this PC

This post has been edited by kuntawakaw: Jun 15 2010, 07:29 PM

single channel bro.. everyone can do that..kekeke
downgrade kaw2..dah lame dah bro..since i let go of my 550BE..
i tot by june can gather enough money for thuban..jangkaan meleset..xckup duit.

eh?Where got..kekek

according to antonio..if u can disable the use of share mem...disable it..use sideport only...
but last time (i cant remember what mobo..TA790gx 128M perhaps) i just cant disable the UMA, just put the lowest value possible... like 32Mb perhaps..it helps alot in HTT oc..kekeke..

@ah khoo..
ta690 already richer then me... kekeke..no need to know which brisby also can determine..(and im guessing it will be 6000+ brisbane,kekekek)

EDIt:long time no see lim... if i havnt seen u in person..i must be missing u now (since i tot ure a girl last time )
till now money not enough..
so postpone..kekeke.. but must be before next year

i still remember..when all here stays the NB freq below 2.5ghz..due to the comfort vnb..u push up to 2.7ghz and post at verdict's database..kekekeke.

This post has been edited by kuntawakaw: Jun 17 2010, 04:51 PM

u have to test to get more..kekeke..
tweak ram..or perhaps max out ur CPU..
HT link i 1200mhz also satisfied edi..kekeke (owh crap..fogot..mine mobo is older HT link..kekeke)

y dont 870..some got 2x PCIEs also..cheaper... kekekeke..
do remember on FX..2cards CF will get 16x..but on GX only 8x

@cloudwan..
happy birthday bro.. may ur wish be granted...1090T right?kekekek

@verdict..
with that avatar again..annoyed..kekekek

i donno how reliable this table..since this table been in my PC for long time..so i cant remember the sos and the reliability..kekeke
but it does make sense to me..

im not so sure..iirc..last time sifu antonio recommend some low value. (<600 perhaps)
anyway..just blend.. or u can try in place large FFT ( i hope i had the name correct)..

what i know..
small = cache
large = ram
IMC donno..kekekek..

HTT yes..sure u have to tweak it to find the sweet spot..
HT link..u can leave at 2ghz +- abit.. will not increase performance.. it might increase if use IGP..
the volt.. sometimes when i OC..i give some extra volt to HT and NB..legend said that it will increase the stability..kekeke
after finalize, then will reduce back if stable.kekeke

wait.. HTT (BUS SPEED) is the one that stock at 200mhz..HTT x multi = CPU freq
another 1 is HT link..both is different thing..
HTT x HT multi = HT link speed..

i wonder what board u use eh? y stock at 800mhz?
since both u and i donno what FFT used to stress the IMC alone, i suggest to blend.. so it will stress both CPU + IMC inside ( and ofkos ram included)
or wait tomorrow for sifu to come out ( i doubt they will..since most of them esp Ah_khoo and cloudwan only spam here during office hour )

kekeke..so the 800mhz is the idle C&Q state for ur CPU right?
newer mobo where got stock at 800mhz.. if my mobo ye la...stock at 1000mhz..kekeke
i usually alter the width only..16.i donno the benefit..but like the number instead of auto.. others seldom touch.. only sometimes the volt..
if u want to OC the HT link..go ahead..but just dont make it more than ur NB freq..if more, then u have to korek2 ur CMOS jumper lah..kekeke

edit:repost answered question

HT link..u can leave at 2ghz +- abit.. will not increase performance.. it might increase if use IGP..
the volt.. sometimes when i OC..i give some extra volt to HT and NB..legend said that it will increase the stability..kekeke
after finalize, then will reduce back if stable.kekeke

This post has been edited by kuntawakaw: Jun 20 2010, 12:42 AM

tips? mix HTT oc and multi even if u get BE chip..sometimes it will yield better result..
and also..the vcore? ganas betul pkai budget mobo for this task..kekekekek
cool ur mosfets bro.. or else ull be PCless..

@ah_khoo
pls bro..joking.. pls take no offence
kekeke
ganah ram..what chip?

@selferino
great..kekeke..inilah asam garam OC.. if want prime stable at high voltage, u shud done it 1st week after buying..kekke
got burnmark?if no go RMA..and get urself a new premium mobo leh..keke