don't have dslr.... sorry... will snap better picture later... gimme 1 hour...

this saturday will be running leak test... 1 hour leak test lah..



latest update due to special request



i was suppose to pay my phone bill, then i park in front of hardware shop, my hand so itchy that i couldn't "tahan" so go inside and buy some clamps... damage is rm5.70

This post has been edited by mato89: Mar 10 2010, 01:11 AM

now i can see it clearly dude, the barbs from bitspower. i thought you're grabbing some compression fittings earlier

so your tubing is 1/2" or 7/16"? if it's a 7/16" you don't even need a clamp.. it looks more terrific without it like a million-dollar-pc rig

This post has been edited by kInOzAwA: Mar 10 2010, 01:18 AM

7/16".... ya.. now i realize, i tried to fit those tubings into the pump, so damn hard, luckily i got some secret "technique"

use lighter or push it slowly.. it can be fit by then.. without using clamp is better because it's not easy to take off. 7/16 when put on the 1/2 barbs is super tighten already man.... it looks better without clamp

clamp can spray black... hahah... nevermind... will see how leak test goes..

hahahaha better you fit the tubing to barb first.. let see, how hard to go...

http://www.xtremesystems.org/forums/showthread.php?t=212017

best clamp eva

hahahahaha if like that.. i sokong... better looks

anyway mato89, you're using feser cooling fluid, need no worry if there's leaking somewhere.. but if can, please don't because it's expensive.... i already tested it while my pc is running.. like nothing happen...

This post has been edited by kInOzAwA: Mar 10 2010, 03:15 AM

i know i know... i am worried la.... since the intake and discharge head for the pump should be tight, then ok la, i should be worried about the waterblock and reservoir... thx for thos advice above

wuiyoh...expensive coolant but very worth it...wonder if u shud get some...

at first i doubt that it will be enough but, 1L is a lot.

ahahahahaha...but nevertheless someday ull have to drain the loop right...n i absolutely hate it if i had to halt anything i felt like doing just because the thing needed is not there...

ever considered using food dye + distilled water??

but the colour of the dye fades after some time..

lol... distilled water i can just "take" from laboratory... lol... there is even deionized water... water have so many type, can do review on which type is better lol....

now that u mentioned it...next week i go lab find those things if available... lol










mau acid, alkali, ethanol or anything chemical just pm me... hahaha, can even prepare which concentration u prefer lol

wuiyoh...i wonder if u have a fluid that very slippery like oil but can carry a lot of heat...got alittle project...

why oil??? even if the oil is in solid form, it would gradually melt if you paste it onto hot surface and it might or will ruin your hardware... but if you still insist, then i could only recommend petroleum jelly or also known as vaseline...
oil has higher boiling point than water, but they could conduct heat equally the same.. but if you include solid, copper is the best, since tuniq tx3 is 6.00 something (refer to label behind), the second choice to replace it is mercury, but, u know lah mercury very dangerous...

everything including Feser cooling liquid will fade after some time laa reiben

a clean without pollution distilled water will do... righttttttttttttttt....

yes siput, you can try out a mineral oil as a solution. maybe you can pour down the oil into your rig .. no damage bro, believe me

hurmmmm...mineral oil motor?will try dude...thanx...

seriously?

is it april foot's yet ?

i didn't know that lol