Outline ·
[ Standard ] ·
Linear+
♦ ♦ ♦ PROTON SAGA BLMCLUB V10 ♦ ♦ ♦, The Journey Continues...
|
klk89
|
 Jun 29 2010, 04:16 PM
|
Getting Started
|
QUOTE(l3iTi @ Jun 29 2010, 09:25 AM) hei guys...how long does your battery last? The original that comes along with the car when you first take your car... Darn...my car suddenly battery die liao...cannot start car.... Was thinking of bringing my car this sat to service...who knows the battery din last that long -.-" Anyway, my car is only about 14mths old... I had the same problem like u as well. It happens to me twice. Last week, it took me more than 4 times to push the key to START for more than 10 seconds for it to start. Before this, so forumers said that it might be the battery causing the problem. My car is almost 1 year plus. I don't think the battery would so fast dies off even though its maintenance free. I think it should last at least 2 years. Going to bring my car to SC to let them check. See whether is my battery low or starter problem. This post has been edited by klk89: Jun 29 2010, 04:26 PM |
|
|
|
|
|
klk89
|
Jun 29 2010, 11:53 PM
|
Getting Started
|
QUOTE(JimboXE @ Jun 29 2010, 04:37 PM) try peeling off the maintenance free sticker & check if it is maintenance free or need to add distilled water......u might b in 4 a surprise....  What to do...after let the SC people check then will try and DIY myself if there is not problem exist. =( |
|
|
|
|
|
klk89
|
Jul 24 2010, 02:28 PM
|
Getting Started
|
QUOTE(kari_convention @ Jul 23 2010, 08:50 PM) any of you guys have experience in sending car to Hian Shin S.C. at SS17 Subang Jaya? Went there to service my car. Not so good I would say. Especially the workers' attitude were lazy. Plus, they took hours just to rectify my rear brake screeching noise every time I send it for a service. Until now, my car's rear brakes screeching sound haven't been solved. Not recommended. Suggest you go either Glenmarie or Jalan 222 there. This post has been edited by klk89: Jul 24 2010, 02:31 PM |
|
|
|
|
|
klk89
|
Jul 24 2010, 11:05 PM
|
Getting Started
|
QUOTE(kari_convention @ Jul 24 2010, 05:34 PM) but i have 60K free labor service with them since i bought the car from them. Usually how much the labor charge cost and what the oil they use/recommend? Thanks I can't really give you a figure but estimated is around RM56++ for their labour charge. As for the oil, they will use Shell Semi or Fully synthetic depending on your preference. They will show you a list of things to change and will calculate it roughly how much it cost for the whole service. If not mistaken, 60K service is a major one. Presume it would cost alot. Not too sure tho, you can go there and ask them. Since you had the free coupon, go ahead then. Can save you some money. =) This post has been edited by klk89: Jul 24 2010, 11:06 PM |
|
|
|
|
|
klk89
|
Jul 28 2010, 09:28 PM
|
Getting Started
|
Presume 20K is a major service, how much estimated for that service? I was told by my SC it costs RM500++. Was it that expensive for a major service? @.@
This post has been edited by klk89: Jul 28 2010, 09:29 PM
|
|
|
|
|
|
klk89
|
Jul 29 2010, 08:55 PM
|
Getting Started
|
QUOTE(CyberKewl @ Jul 29 2010, 08:47 PM) that's why i'm wondering has anyone claimed before? where to claim? I claimed before for my rear windshield window. Its at USJ 21/11. |
|
|
|
|
|
klk89
|
Jul 30 2010, 01:54 AM
|
Getting Started
|
QUOTE(smokey @ Jul 30 2010, 12:23 AM) my stock tint also growing bubbles... give us cheap tint...haih Safetint not good one. Even the ones the replaced for me only took them approximate less than 1 hour to finish.
Added on July 30, 2010, 1:56 amQUOTE(zoomckng @ Jul 30 2010, 01:36 AM) saga blm comes with tinting? from factory? or done by SA? Should be from factory. As the newer M-Line comes with tint installed. This post has been edited by klk89: Jul 30 2010, 01:56 AM |
|
|
|
|
|
klk89
|
Jul 31 2010, 12:49 AM
|
Getting Started
|
QUOTE(CyberKewl @ Jul 30 2010, 07:13 AM) Oh? Need to make appointment? Also can go there on saturday to claim? Better call them to make an appointment so that you will get your's done fast. Mine took less than 1 hour for them to finish install the new tint for my rear window.
Added on July 31, 2010, 12:50 amQUOTE(smokey @ Jul 30 2010, 10:50 PM) the rear demister will spoil or not after removing your old tint? So far after they had removed my rear tint, and installed a new one no problem at all. Not to worry. =D This post has been edited by klk89: Jul 31 2010, 12:50 AM |
|
|
|
|
|
klk89
|
Aug 12 2010, 11:09 PM
|
Getting Started
|
Hi...I wanna DIY for my driver's side door panel. How many screws to be unscrewed before we can pry open the door panel? Did anyone DIY their Saga's door panel? Coz my door's rattling sound was unbearable. Thanks.
This post has been edited by klk89: Aug 12 2010, 11:09 PM
|
|
|
|
|
|
klk89
|
Aug 13 2010, 09:22 AM
|
Getting Started
|
QUOTE(sa10 @ Aug 13 2010, 07:20 AM) for front door got 3 screws and 6 clips  Do you mind telling me how to remove the 6 clips that you mention? I only managed to unscrew 3 screws and still cannot pry open. >.<
Added on August 13, 2010, 9:26 amQUOTE(x_kink @ Aug 12 2010, 11:34 PM) same with me bro..really annoying Even normal cruising at 50km/h the sound is so annoying. I guess DIY your door panel with sound proofing materials can reduce the rattling sound plus enhance your sound system. As some members already did that on their car. I can't pry open my door panels after removing the 3 screws. Waiting for help here. This post has been edited by klk89: Aug 13 2010, 09:27 AM |
|
|
|
|
|
klk89
|
Aug 13 2010, 03:19 PM
|
Getting Started
|
QUOTE(sa10 @ Aug 13 2010, 09:47 AM) » Click to show Spoiler - click again to hide... « here u are the clips where located. just use the bare hand then it is enough. Thanks alot for the photo. Will take it as a reference. =)
Added on August 13, 2010, 3:20 pmQUOTE(coolkwc @ Aug 13 2010, 11:56 AM) Make sure u loosen the handle first. For the handle, u need to push and slide towards front, after loosen that, the u can pry ur panel using ur bare hand, pry at gap under the speaker, there are some gap there, no need too gentle and dun worry as u won't damage it one. After that u have to seek your way to remove the stucked handle out of the panel before u can totally take off ur panel, word is hard to explain. Haha...at least you have give me some precautionary steps before pry open it. Will DIY it later tonight. Thanks. =D This post has been edited by klk89: Aug 13 2010, 03:20 PM |
|
|
|
|
Quote
0.0512sec
0.40
7 queries
GZIP Disabled