err.. PWS bought 0929 ?

i still thought of buying 0929 and try my luck

ahemmm ahemmm M4 aHHhhheeeMMMmmM A78 ahemmm ahemmm -E ahemmm ahemmm!!!  

400 vs 600....aheemmm aheeemmm kuhkuh uhukk uhukkk uwaaeeekkk...

Got....my ASUS M4A78-E    I bought the Biostar TA790GX 128M for RM365 and the Asus was 35 more than the Biostar which lacks PWM Heatsink, E-Sata Port, had a thinner Alu NB heatsink and doesn't have a sticker.   
Well before the 1302 Bios I was half-hearted with it. My heart was accusing my head to be too stupid to get the Asus and sold the Biostar. But everything change and after the 1302, both parts of my organs live happily ever after

For the RM35 extra, I'd say go for it....

some memory overclocking on HyperX ddr800.. really hard.. trfc set to 105ns, vdimm 2.0v, timing change to 5-5-5-15-20-2T
manage to bring down the latency finally, if not almost at 70ns 

oic...
thanks guys...
cz 2moro going buy =.=
hope i can get the luck for quad core..
haha

lol.. my seller dun gv me low end CPU lo..
sad 
i dun hv much $ ma..
so need unlocked it try my luck lo..
if 2moro successful unlock i treat u YAM CHA (only Kepong)
haha..

For bro CV6149,

[attachmentid=1167791]

-pWs-

Before u do the following, I assume you are already bootin into Windows and still can't detect even after installing AMD drivers....

Probably the jumper selection for the CD-Rom n the HDD are both the same...Ensure the selected is appropriately assigned according which connector you are using on both components... Lets say you 'cucuk' the end of the IDE Cable into the HDD and the middle connector into the CD-Rom, then the HDD jumper should be at Master and the CD-Rom jumper must be at Slave....

If u have done that and after booting still cant detect, install only one component each boot on either connectors, for example; u cucuk the HDD with both end and middle connector of the cable see if got something. If still undetected, try swapping cables or test the current cable and HDD CD-rom combo on other computer/mobo.

If cannot detect also, reset CMOS, remove battery, and leave for 5-minutes, the put back on and boot...

If cannot also, then ur IDE controller kaput!!!...wakakaka..kasi RMA...
Jom!!!

did they test b4 exchange or did the guy that handles ur request simply takes a new board replace the serial number with your previous board, print a receipt and then restock em back?? (typical style) 

All the best!!!

not into OC mode at this moment!

after done several checking! amd its confirm that this mobo = SHIT!!!

poor quality i think!

lol... d distro is Convergent rite? I had not so gud experience w/ em here as well when i rma d board w/ pci-e port issue. end up bring d whole rig to d service centre. 

actually it's all bout luck when rma, sometimes u kena easygoin stuff (which is gud coz not much question asked & short period of inspection) while sometimes u kena those stuff who is CSI wannabe... 

d board itself is great, as solid as d nf4 ultra-d in d gud old day of k8. it's also d only am2+ board i regret sellin (sold it for d reason that it can't run unlocked cores stably mana tau now they finally come out w/ d bios  )...

it is value..
kingmax value ram with d9kpt..

1780mhz cl7...still rocks yeah...but single channel yo...

performance ram too pricey now.. im waiting it to lower the price 1st..then grab for sure...

ah_khoo..
80mm fan blowing + ramsink (not the clipped heatspreader..the fin one) can i put 2.0vdimm? for OC for sure..not 24/7

The ram from hikari85??

-pWs-