can i know use what for cut acrylic panel??

jig saw or any saw lo.. hey use acrylic cutter nice to cut ha?will better then jig saw?

Using arcylic cutter will be more straight and easier if using with ruler...

but it be more works and also if not careful... it will break...
sure is better if u can get one...

@calvin
waaaaa....very cun one...ahahahaha...u started building already ka?huhuhuhu...cant wait...

yup2...arylic cutter is important...especially if u want to do detail cutting...

haih == really no straight at all =(
thinking how make it straight now ..

here some pic i juz done cute side panel and the rom bay


why cut not straight T_T..moody

what did u use to hold the acrylic while cutting?

table + chair T_T i dun have the work sation table tat table have hole in middle...
argh............................................................

place a 100grid sand paper on a flat place ( table or floor )

than move the arcylic pieces thru and flow... sand it down... not a big problem...
it is normal anyway.

This post has been edited by tjay_tj: Jun 11 2009, 06:54 PM

like tat the acrylic will become small a bit o the side @@..

to get a sraight cut...u could align the acrylic on the side of the table...then...measure so dat its straight..then use the...'apit G'(dont noe whats its called in bi)...huhuhu...i used on mine...n...got an almost straight line...

apit G?o.o tools?btw is 2848calvin here!! i at he house now =) he help me cutting

This post has been edited by ch3n87: Jun 11 2009, 08:11 PM

apit G is called G clamp in english
yup that right... than clamp another big ruler to guide the jig saw and u will get a nice straight line... 2 G clamp is prefer

yup sanding will make the arcylic smaller... but that is only buy 1 or 2 mm smaller, if u have the time to sand... it is always better than not stright line... it is the easiest solution...
that u will need to sand the other piece to make it same.

again u hack into chan account again... haha... joking only

This post has been edited by tjay_tj: Jun 11 2009, 08:54 PM

hehehe no la he got 1 pc at living room and he using so when u help me cut the acrylic i come and see my tread =D
pss pss...ch3n inbox so full =P wakaka juz now i go buy acrylic cutter but =/ no use at all so hard to cut

omg omg ch3n coming see ya~~~~ shhhh......dun tell he arr bai bai later i back home juz on9 la

@calvin
buy a arcylic cutter,is the best way to get a straight line.
or use a wood ruler,2 apit G. use the wood ruler as a guide.

@tjay_tj
thank you for offer,if need ur help later i wun be heritage to ask.lolz..
where u study now ??

no problem bro
i now study at tar college...

so bro, how thing going?

juz reach home now still thinking =/sigh this few day otak dint turn no idea at all

hohohoh...go n dream lo...then after u dream up of an idea go skecth on paper lo...huhuhu...anyways...i think ur design on the sketchup is ok already...but to me u still need a few touchups here n there...

p/s think about what u want to put inside the case...then..think how u want the case to look like...simple ke....modern ke..it helps to generate idea..

hmm...@@ otak really need go RMA 1st .. today ch3n87 help me cut out the acrylic already i juz need draw a side and cut it smaller now i finding the hole drill 12mm 1

modding is like that de lar...

i use 3 month to finish 1 project...
go rest if tired...

about the drill... it is 1 inch de wor... i suggest to drill using normal drill and file/sand it using a file...
or u just go hardware store and buy one 1 inch drill bit/hole saw