i noe single core sure vy bore... now get this oso for tahan jeee..

nanti kan pop up something special for all of us here... 955 kang

waaaaaaa.. nice wor~
easily hit the 3GHz

cyberloner ans ur ques..
CnQ is js a tech for power saving, but normally when i ply game i will disable it, coz the program(game) still not 100% make it run at the top speed,
sometime run at lower speed then the game will laggy..
so basically i oni use CnQ when not gaming..

no F3 ar..

dun worry bro, using CnQ if chip die can go RMA, if OC die thn no RMA, u dare to OC no dare use CnQ

dun worry bro.. js go on, if prob come out in the long term usage, thats the time to upgrade another new chip

ya thats true.. as long as the vCORE is adjusted frm the stock 1 consider endanger

but for oc propose, we will consider the 'endanger' frm the point of view of the temp and the vCORE for the chip,

where as we always said, as long as u keep ur chip in good temp, u can increase some vCORE for ur chip,

but for 24/7 usage normally we not recommend more then 1.5v ;
but if u can really keep ur chip in a low low low temp, then u may try higher vCORE for higher clock.. (macam verdict, he wan do 1.6v )

but as xixo told, sometime vCORE too high also cnt get stable, may coz by the HEAT of the too high vCORE..

and wat we do or we wan do is with lowest vCORE to get the highest clock

for me, honestly i would say cpu 100% loaded temp below 60c is consider good temp. (*this is not for 45nm chip, as 45nm chip suppose lower then this)

if loaded not over 60c idle will around 30-40c i thk...

its js normal case there, when running on CnQ, u can see the usage 100% when u js simply open a program, aft that it will goes bec to idle, js a second..

this is call CnQ wat.. goes to max when loaded, goes to min when idle, if it cnt naik turun naik turun itu yang problem tuu...

naik turun naik turun baru siok kan


------------------------------------

added:

@nidup

9550 can get 2.8 stable oledi good, get a 3.0 is vy good

This post has been edited by cdlim87: Apr 12 2009, 07:10 PM

intel kaya mate...


3.2GHz oledi for the 9550?? nice

actually not much diff la... all is stressing software.. actually either pass 1 of em consider good, as normal usage pun seldom running 100%loaded sooo long time 1...

for me its ok..

but ppl stilll say the line up: prime > orthos > occt

like me if use orthos, we can js tune the priority, the highest u put, the heavy the load... so if u pass high lvl orthos its consider vy good oledi..

wat is ur setting curently?

screennie

bro, how bout u try multi x15 ?
lowering a bit ur HTT(214) and vCORE(1.4-1.45v)

BTW wat vCORE when runing on 3GHz?

edit:
if u use higher HTT, u will OC ur HTlink + ram too... and u r using KVR?? may dun OC ur ram too much..

default? clear CMOS

This post has been edited by cdlim87: Apr 13 2009, 02:37 AM

aft 1 month send ur chip to me, i help u OC.. LOLz

actually u need tweak more... as i said b4 128M got wat wat cpu configuration 1 till 6 or something like that..

and diff bios will do diff job with the cpu config.. IINM la... as last time i has told by bro sepul when he is activ around here..

he oso used 128M for few weeks, then change to DFI oledi... thn sold off all his stuff...

so u gotto develope more on ur board...

its a phenom too(k10).. js name as athlon oni..

dun use AOD, ur board not suitable with it..
CyberFusion? need ori warcraft..

yup.

hang o wat??

not always higher vCORE can do better, too high vCORE will coz a high TDP too.. so u may try the lower vCORE..
do u tried b4 wat the max clock can do on 1.45v??

good idea

---

Added on April 13, 2009, 11:43 amdun use aod lo xiukeong.. if wan AOD DFI is required

7750BE 3000MHz is can do for each chip i thk

if it cnt even clock 400MHz, how do it name as BE

ohh.. the config us for high HTT.... ic ic thx for the info... 4gt ad...

as last time bro sepul oso clock his 38F3, with multi x10, it really need a high HTT... thats y ply much with the cpu config

This post has been edited by cdlim87: Apr 13 2009, 11:43 AM

who say no challenge? js the state is diff now, b4 this is aim 3GHz n above, now is aiming 4GHz n above..

so the challenging still there oni at the higher state...

no point if still stick at the 3Ghz with new architecture/new design/new rite..

---

Added on April 13, 2009, 4:44 pmreally org kaya nie!!!

can bios can all the things

This post has been edited by cdlim87: Apr 13 2009, 04:44 PM

WaterCooler III??

---

Added on April 13, 2009, 5:11 pmits okie bro.. no jk no fun..

eh, but really la.. 4GHz is not such easy to hit even own a Deneb on hand..

really skill/money/luck dependent

This post has been edited by cdlim87: Apr 13 2009, 05:11 PM

the real propose cheat u coz dun1 u kena poison by the WC III, ltr pula xixo everyday bz DotA..

yaya.. must try the lower vCORE, dun always direct bump to the top... step by step.. may try 1.4v-1.45v see wat the highest it cna do..

all wan shift to phenom II

so ur GC x laku? come boro me ply ply 1st..

ram? KVR 1x 2gb , normal high wanted..

sarah wan tell u 4850 is ready for u..

nak jual ulang tahun kah nak beli nie??

itu nice ram, tp xda , still aiming KVR oni

400RM?? DDR3 ram is calling u..

waiting for AM3/DDR3 la tu... katanye xda duit

790 chipset is better for OC propose..




_______________________________________________________________________________

wow.. 2nite so many ppl....

9150e is born for HTPC

i dunoe wat happen to ur chip.. suppose can easily sit on 3GHz..

if earlier chip can do 3.2GHz easily, coz most of em can hit 3.3-3.4..

but latest chip seem always had prob even 3.2GHz.. so try ur best to get 3.0/3.1/3.2

swt =.="

wat happen to ur baby...

its too serious now... clear CMOS n clock again, u sure u clear the CMOS corectly?

aft clear CMOS, dun use AOD anymore, clock at bios enuf...

This post has been edited by cdlim87: Apr 14 2009, 03:50 AM