Jetway mATX 790gx DDR2/DDR3 combo mobo review spotted!
http://www.eteknix.com/reviews/jetway-ma3-...d-video-review/

i'm in midst of setting up my Lian Li PC-v351


This post has been edited by fr0sti3: Jul 10 2009, 01:19 PM

i got my v351 from karom @ butterworth / penang
got it COD since i was around there

he's got lotsa lian-li stuff

pc-v351 user manual


GPU sideview


there's space below front 120mm fans to route cable,
front input panel can be remove, only 2 screws holding them on


modular PSU helps alot, u can start routing PSU cables b4 installing PSU


PSU installed


all up & ready to go!

ok i'm lazy now, will bench laters

yo buck, yer using Dell 20" ultrasharp too?

well if yer PSU got intake fan, u can put a thin fan on your CPU heatsink to pull air up into the PSU~

found something interesting...
aerocool m40 sff/matx casing (too bad m'sia tak da)

http://www.xbitlabs.com/articles/other/dis...f-system_3.html

i changed my stock heatsink to coolermaster geminii s,
cooler fan is blowing upwards lo. idle temp 41c +- in non aircon room

don't have my cam with me yet

some updates on my Lian Li PCv351

- GeminII S, fan is pulling air upwards to the PSU
- two CM 12cm 90cfm fan with zalman fanmate 2
- throw away my old 40gb HD, move 320gb HD to DVD area~

Phenom 720 (OC to 3.2ghz) 52c load during prime95 test for 1 hour ^^



i guess now all i need to do is remove the HD cage & put a 92mm fan there for better exhaust
will get prime95 test screenshot later afterwork x_x

infront got vents as well as bottom of the front plate~

SG05 & SG06 damn hard to do cable management since it's soo small (itx)
not much clearance between CPU & PSU oso

w00t got my 4890 vaporx
it fits into lian li pc-v351!

Pics


This post has been edited by fr0sti3: Aug 24 2009, 07:10 PM

it's because my PSU 6 pin cables are damn stiff near the ends x_x
i bend them around 80-90 degree angle

4890 vaporx is hitting 80c on core & 90c on shader/mem when running 1680x1050 4xAA furmark, i think i need better exhaust...

tested 1 hr with crysis warhead, it's around 70c on both core & vram
i think furmark maybe too ganas sometimes... oh wait i OC it at 900mhz / 1100mhz

thx for the suggestion guys

actually the OC was for furmark only... i see 90c on vram i oso sweating bullets... max OC was 925mhz / 1120mhz, go beyond got artifacts d

yea, i game at 850 / 1000 for now.
after 3 months of v351, i would say air flow problem is not enough exhaust.
wanna remove the rivets for HD cage, but scare later too heavy handed

hmmm decision decisions... speakin of which i'm planni to get Xonar DX to pair up with ATH-AD300. good budget pair up ?

ah ~ if i sit my sound card next to the GPU,
GPU heat shouldn't affect it right ?

well since it's a SFF casing

+1 to smaller nice pic

erm... the rad looks er.. out of place
back mounting will be alot better, the plate & tube are not detachable ?

CM hyper tx3 can fit... but u'll need to pancung it's kepala

why not use a tower cpu cooler ?
u got very nice clearance for it.

oh yea, nice placement for steelseries sticker ^^

ATE has v351 there & accesories for it too, btw conventional thumbscrew is 1mm bigger than their holes on side & back panel

he wanna use MCE wif remote controls ?

---

Added on September 15, 2009, 10:10 amsry for double posting,

saw this model onsale at shop opposite digital mall


http://global.aopen.com/products_detail.aspx?Auno=2063

This post has been edited by fr0sti3: Sep 15 2009, 10:10 AM