meh, i dun think i have d time to do bulk... some more, no enuf capital$ leh...

this was my best w/ stock volt b4...

http://forum.lowyat.net/index.php?act=Atta...=post&id=556561

semangat oc berkobar2 in u bro...

**vDIMM 2.0

uik? why so low?
and u didnt pass memtest?

loosen ur MAL : 10ns, it help?

This post has been edited by xixo_12: Jan 4 2009, 11:29 AM

always stuck with memtest.... if i OC untill 3300MHz sure no prob... can pass all ....

hmm.. will try out MAL 10ns...

any else can tweak??

ok try this, not too loosen

5-5-5-15-20 or 5-5-5-12-15
MAL 10
vdimm 2.0v

then test first.. let see it work or not

This post has been edited by xixo_12: Jan 4 2009, 11:35 AM

will do

master xixo i tried ur method and still under construction but with a small improvement luckily my mobo comes with memtest so far i test all pass test.....but why in memtest it reads my ram speed 711MHz but in cpu-z tab it reads 640MHz...

maybe bugs there.. i'm not too sure.. u can refer to divider table what is ur exact speed..

test using orthos also can, ram stress only..

recommendation: try with a lot n different software.. so u can judge later it's so stable or not..

aiyooo thats why la...u know arrr master memtest past but super pi n hyper pi both stuck in 128k test
btw vdimm is 2.0v n 5-5-5-15-20 ss dont have now tomorow i post ss....

haha.. dont be too dependent and trust on them.. 1 fail, 1 pass considered good..

emm, try to delete pi_rec.dat2 in Superpi/hyperPi folder and run it

wah sudden all start ocing kaw kaw, getting ready for the oc meeting?

hehehhehehehee damn this ah soo cekik voltage 3.0 @ 1.22vc hehehheehee

temp not so nice also hot hot hot

here r some pic before my board comfirm dead and my tak cukup besar htpc case






seems need to mode some area just to fit in my psu

This post has been edited by sepulgilo: Jan 4 2009, 02:13 PM

Anep, Try to put ur v-core to 1.5V (if not enuf the limit is 1.55v) and adjust the multiplier to 17X200 u can achived 3.4Ghz den jump the FSB to 208 x 17 = 3.5Ghz.. i tried it before and it works.. But not with a AX78 mobo la.. but u still can try n good luck..

both setting fail la bang xo...
this ram really make me

wow...
haven' really try oc'ing ram...

all OC suddenly

u use lower divider rite (400),
if change to 533 with same setting, fail also?

NONO... it is bcoz of.........


hvn try with 533... js try on 400.... owh, same setting but apply at 533 may get stable ar??

i just wondering, it's might be divider problem..

when u set to 533, ur ram still running under stock speed .. so not a big problem..

ic.... so will try again ltr on...
but should be no prob with setting 400/533/800
frm cpuz, we can saw this 3 setting...

try this two divider 533 and 667

i'm sure u will not pass with divider 800

i noe.. if 800 will OC the speed of this ram oledi...
but ppl told me thy use KVR too, can push to 950MHz with 2.0vDIMM, but how come mine cnt ....
thy r dark side user...