haha of coz every 1 who have TT product can join la...

hey, i just bought TT sonic tower hsf. its damn big & light.. the weight is only half of cm hyper6. hehe.. but i have problem with installing it, coz it stuck with my zalman vga hsf & for solution, i have to take out the half heatsink in my zalman.

i'll post some pic later. now just finish installing & oc it. hehe... full load 45c.

err... i can't see the pic.
issit just me? or...

haa???? my comp got problem or what?
i only can see the word "user posted image"
k la nvm.

nice.. looks clean

u should join coolermaster league also, since u r using coolermaster cable

This post has been edited by rezzz: Apr 3 2005, 05:35 PM

i'm using it now..
it's not heavy at all..
but i have problem win installing it. coz my cpu location in mobo is too close with ram slot & vga slot, while i'm using zalman vg aheatpipe which is very big.

its not heavy at all... it will not break ur mobo..
the weight is almost the same weight as pipe101. much lighter than cm hyper6.

not really nice if u didn't put extra 120mm fan. i put chapalang 120mm fan, the fan i can say have very low cmf(i dunno how many cmf) but i believe its lower than other 120mm fan. (later wanna buy 120mm fan again)

idle dunno coz never idle but sure its below 40c, load (folding) around 48-51c.
note: i oc my cpu. vcore from 1.4v to 1.66v

btw, just now i change to pipe101 again with 92mm TT fan, just wanna try. hehe..
almost no different in performance.

eh, update from my rig. I already do cable hiding just now, but i think not max yet... the idea is from mystvearn cable hiding technique... coz i'm using the same icasing & same PSU, & same cpu hsf as him only difference in colour.
i'll post pic later..

before: last time when i just bought the PSU & casing.


after 1st try:


now:


this is the best part i think.. I manage to turn all the cable to the right side panel except the 20 & 4 pin molex, coz cable not long enough. I didn't make a hole, just use the available hole beside PSU


well.. CCFL switch i put here..


& last.. here what my front door looks like.


still can't manage to hide some cable...

This post has been edited by rezzz: Apr 15 2005, 05:56 PM

coz want to make it 1 brand lo.... hehe... but i'm thinking of changing my PSU to other brand..

soprano the front door shinier..., a bit difference on design also.. other than that the spec all same. & also, front door is plactic. (read from website)

well.. waiting for ur picture darkjedi..

This post has been edited by rezzz: Apr 15 2005, 10:43 PM

no mod at all..
the switch is originaly like that, its sunbeam dual white ccfl with inverter. I just put it in front bay & also I didn't cut or make a hole in TT controller plat.
u see the the small gap between fan controller & dvd drive, i put the cable there & the ccfl inverter is below the fdd drive.

later wanna buy fan grill for my cpu fan & also for side panel fan, scared my finger will hurt again, coz just now my finger accidentally touch cpu fan & it's pain... (stupid me)

sidewinderz: I dunno where to buy spareparts, never saw it, i also scare if one of mypart missing..

when reading ur post "you can remove the useless usb/firewire thing on top of the casing, just unscrew it", i was thinking to make a blowhole there.. but... i dun want to drill/cut the casing.. so sayang.. expensive casing..

then what did u do after u remove it? just keep it unscrew? or u make some modification on that area? mind to show me the pic?

kianwee: ya I dun dare to cut it.. hehe... thx for ur suggestion..

sidewinderz:i just realize u usng white ccfl too. hehe.. for ccfl switch, put in front la.. it will look cleaner for ur ground area,(at least less 2 cable there)
for psu cable part, how do u hide it? coz the pic is covered by sidepanel haha..

wanna ask for all, which led fan have long lasting led? I mean the led can tahan longer than this TT rear fan. coz 1 on my led off already, & the rest 3 almost die also.. wanna replace it.

to put ccfl switch in front, no need to mod. ntw, where u put fan controller for PSU? issit in 5.1/4 bay? or somewhere else? if u put it like mine, u can put the switch there too..

for me its worth.
I even bought it at higher price. (b4 it reach lowyat )

mine modified front door looks only. (issit called modify? )
but i found it's ugly when last month I found better looking material. gonna replace it soon.

do i forgot to post pic here?? (i dun like this texture anymore)


which 1 u all think better?
i wanna redo it. the material that i'm using it now isn't good, i got better looking material, more like CF texture. hehe..



& also what do u think if I put the same material on the sidepanel? so the material wil cover the whole casing, only left the windowed part, all allumunium part will be covered by cf material. will it looks ugly or better?

mine 1 is the 1st pic.
3rd pic i got from internet.
2nd pic i edit from 3rd pic.

so 2nd pic & 3rd pic which 1 better? (talking about the middle silver part. I mean, better i remove the silver line or not?) wanna do it now. now the front door taken out already for reinstalling cf sticker.

need quick reply now.