ham whats ur advance clock setting?the cpu clock drive,pci express clock drive etc

clock drive i set both to 1000mv,while clock skew i set both to 150.cant see any difference pun,maybe jz to pump some juice within ?lol

if u set the multiplier to 2.00 then its 1:1 lo.2.00D

dun think theres any change in features,maybe the design/layout is nicer in rev1.1,and the ddr3 word lol

cpu host clock control of coz nid enable otherwise u wojnt be able to oc

the vcore depends on ur stock vcore and ur oc.increase by a bit will do,after tht run test and if no errors,try lower it or jz keep it if u like

others i all put auto.

yes i keep my 4.1ghz for evryday usage.i dun run my comp 24/7,unless got some big downloads to do which need to keep it overnight.

idle temp @ 38-40c depending on room temp
load temp @ 69-72c depending on room temp

i duno my room temp .it has no aircond.

i apply a bit too much thermal paste whn i mount my cooler,resulting in such temps

This post has been edited by ZeneticX: Apr 5 2009, 11:37 PM

er my vcore is set to 1.343v @ bios.considered low?

lol.i seldom go 24/7 la.will switch off my comp before going to bed evryday.as long the temps are ok at idle any vcore is ok i think

btw e8400 is safe @ 74.1 c according to intel

http://processorfinder.intel.com/details.aspx?sSpec=SLB9J#

my proc can boot no problem on 1.343 vcore running on 520fsb

others setting i just leave it on auto.

but i have a problem too,evrytime i start up my comp,evrything will power up thn off agn for about 5 sec thn power up and proceed to boot.i heard its the MCH voltage,is it?

its not unstable.already benched and tested with prime and linx

whats ur MCH voltage at ur current oc setting?

did u tweak the others other than the MCH voltage?

regarding my problem over the boot up - power loss 5 sec - boot up problem in my previous post,what is this symptom called?gonna do a round search around google bout this

i have tried but then it seems theres something wrong when i play with this voltage.after i press F10 for apply the comp will power down and then turn on,power down then turn on and go on till duno hw many times till i fed up turn off the plug and reset the cmos

bios of coz,the save to cmos and exit key is F10 ma

1.32v....since u mention u used 1.3v at ur last post and u have lower fsb,so i think y not increase it a bit

yes.but the main prob now is everytime i play with the voltage the rig jz shut down and then power up for about 5 sec?then shut down again and keep on cycling till i feel fed up to play with tht voltage agn

if i remain like this (power up - power loss 5 sec - normal boot up) it wont do any harm rite?

alright so i did a search on google bout other users of ep45-ud3p running on 520fsb or higher to find out hw much they set on the MCH.and found out evry1 of them set to at least 1.4v

so i did a restart just now and just set it to 1.42v.and god bless my rig booted up and im still here if not i may end up whole day trying to reset evrything in the bios .

still not sure wheter it solve my main prob during turn on


here's the link if u're interested

http://forums.tweaktown.com/f69/help-overc...fsb-ud3p-30239/

This post has been edited by ZeneticX: Apr 29 2009, 05:27 PM

but dmm i didn't expect 520fsb to suck so many juices out of the MCH.1.4v heh

no wonder when i set to 1.3v+ the comp cant power up


i use the opportunity to raise 2 others as well

CPU Termination : 1.3v
MCH Reference : 0.823v

This post has been edited by ZeneticX: Apr 29 2009, 05:42 PM