Outline ·
[ Standard ] ·
Linear+
Air Cooling Discussion Thread V3, Database, FAQ, Guides and Discussion!
|
hilmiangah
|
 Feb 14 2009, 02:15 AM
|
Kongsi Gelap Elite Ramadass
|
QUOTE(Bonchi @ Feb 14 2009, 02:12 AM) XMP whats that?....extreme memory profile?...if its that..i didnt use it coz i set everything manually in the bios....i presume it should be better than the auto ones....coz i dont want it to be too slow or too fast...1085mhz with 5-5-5-15 is just nice for me i dont wanna exceed 2.1v as it would void the warranty (according to corsair site) thats why...and also..mine was put as standard yes it those thing. but dont know if it really work with an overclocked system. |
|
|
|
|
|
hilmiangah
|
Feb 14 2009, 06:07 PM
|
Kongsi Gelap Elite Ramadass
|
QUOTE(ZeneticX @ Feb 14 2009, 06:04 PM) oh shoot i realize i did a small mistake while installing my crossbow backplate  .i take off the white plastic thing cause i though its part of the double side tape.not a big matter is it? i think that one is to prevent short circuit u know. |
|
|
|
|
|
hilmiangah
|
Feb 14 2009, 06:49 PM
|
Kongsi Gelap Elite Ramadass
|
QUOTE(ZeneticX @ Feb 14 2009, 06:32 PM) but the thing sure damm hard to take off now since the double sided tape is strong  and after i take it out and want to stick bck,use wat? and i cant find any info wheter its paint anot,but the backplate got a matte black finish just cover it with a layer of double sided tape. and get those thick and soft type one. |
|
|
|
|
|
hilmiangah
|
Feb 14 2009, 07:04 PM
|
Kongsi Gelap Elite Ramadass
|
QUOTE(ZeneticX @ Feb 14 2009, 06:55 PM) because paper is not a good (or should i say nt at all  ) insulator for electricity?primary school science  next time read the instruction and manual thoroughly........... |
|
|
|
|
|
hilmiangah
|
Feb 15 2009, 02:56 AM
|
Kongsi Gelap Elite Ramadass
|
QUOTE(ZeneticX @ Feb 15 2009, 02:54 AM) im running at 5:6 ratio nw @ 1094mhz using the 2.40B multiplier.tested using memtest,so far so good nice one. now run a everest memory benchmark test. see how much faster it is compare to the old stock speed. |
|
|
|
|
|
hilmiangah
|
Feb 15 2009, 03:02 AM
|
Kongsi Gelap Elite Ramadass
|
download the trial and u got pm.
|
|
|
|
|
|
hilmiangah
|
Feb 15 2009, 03:12 AM
|
Kongsi Gelap Elite Ramadass
|
tools. and i take u get my pm  |
|
|
|
|
|
hilmiangah
|
Feb 15 2009, 06:29 PM
|
Kongsi Gelap Elite Ramadass
|
when u increase it back does the error still happen??
|
|
|
|
|
|
hilmiangah
|
Feb 15 2009, 06:34 PM
|
Kongsi Gelap Elite Ramadass
|
and Prime stop giving out errors too???
if it does than its the proc not getting enough vcore and not the ram.
|
|
|
|
|
|
hilmiangah
|
Mar 4 2009, 10:07 PM
|
Kongsi Gelap Elite Ramadass
|
i just lapped my e8400 and my Hyper 212 today.
will upload a new result on weekend........too bad i dont have a camera to snap the pic.
the proc wasnt to mirror like but close enough.
the grit use
400>600>800>1000>1500>2000
|
|
|
|
|
|
hilmiangah
|
Mar 4 2009, 11:09 PM
|
Kongsi Gelap Elite Ramadass
|
relax bro. wait for a couple of week then i can give u a pictar taken with a DSLR tunggu my lil brother back from Penang. but from what i can tell............its cooler by around 5'c max. |
|
|
|
|
|
hilmiangah
|
Mar 5 2009, 12:25 AM
|
Kongsi Gelap Elite Ramadass
|
i use those dry technique.
watch some videos on yotuube as a baseline.
and yes its OEM and thats why i do it
|
|
|
|
|
|
hilmiangah
|
Mar 5 2009, 12:39 AM
|
Kongsi Gelap Elite Ramadass
|
QUOTE(tot31 @ Mar 5 2009, 12:37 AM) 5C drop is really worth it to do the lapping.  sadly that only apply on Prime..........LinX temp stayed at the same level..........i think its maybe bcoz the last time i run it.........it was on the 32bit os and now im running it on 64bit os. but all and all im happy.
Added on March 5, 2009, 12:40 amQUOTE(ham_revilo @ Mar 5 2009, 12:38 AM) lapping proc imo its dangerous to use the wet method. if a small drop of water slip into the circuit and not was not dried properly then you will end up with a dead prob  i use the wet method on the heatsink otherwise the friction will always make the sand paper im using slipped. its either that or my tape wasnt 'spidey' enough. This post has been edited by hilmiangah: Mar 5 2009, 12:40 AM |
|
|
|
|
|
hilmiangah
|
Mar 5 2009, 09:30 PM
|
Kongsi Gelap Elite Ramadass
|
im running a stress test rite now base on the same setting that i run for this database here.
|
|
|
|
|
|
hilmiangah
|
Mar 5 2009, 09:38 PM
|
Kongsi Gelap Elite Ramadass
|
here is the result 
a 2'c drop while running Linx. not bad for a RM10 job. |
|
|
|
|
|
hilmiangah
|
Mar 6 2009, 01:36 AM
|
Kongsi Gelap Elite Ramadass
|
another result but this time with Prime95. 
and its a 2'c drop on the 1st core and a 5'c drop on the 2nd. too bad i dont have the old screenshot of the b4 lapping process. |
|
|
|
|
|
hilmiangah
|
Mar 10 2009, 04:40 PM
|
Kongsi Gelap Elite Ramadass
|
QUOTE(dro @ Mar 10 2009, 01:04 PM) the basic of tightening bolts is doing it in a cross action letsay ur bolts are placed at 1-4-7-11 (clock position) so u start by tightening 1>7>11>4 tight it loosely on the 1st round then only you tighten it properly once everything is in place this can avoid flexing  that is the way i do it with my Hyper 212. |
|
|
|
|
|
hilmiangah
|
Mar 16 2009, 12:55 AM
|
Kongsi Gelap Elite Ramadass
|
As promise......this is the pic of my lapping project Main Star 
Co - Star 
Main Star in her bed 
thats the pic for now...........later in the week i'll release some Fenrir. |
|
|
|
|
|
hilmiangah
|
Mar 16 2009, 09:53 PM
|
Kongsi Gelap Elite Ramadass
|
QUOTE(aztas_mon @ Mar 16 2009, 09:00 PM) aztas_mon/ Tunix MX2/ C2D E8400@4.3GHZ(43.3% OC) / 1.31V/ xigmatek s1283/ 43c/ 66c/ Non-Airconditioned/ Orthos at least 20 minutes of stressing is recommended. |
|
|
|
|
|
hilmiangah
|
Mar 17 2009, 02:31 AM
|
Kongsi Gelap Elite Ramadass
|
QUOTE(verdict @ Mar 17 2009, 01:48 AM) start at 600 > 800 > 1000 > 1200 > 1500 > 2000 |
|
|
|
|
Quote
0.0621sec
0.78
7 queries
GZIP Disabled