i think he looking for this so can control 212+ push pull speed just 1 by 1 header

never know got this kind of cable~~

What do you guys think of Spire Coolers (Gemini & Eclipse II)





From FrostyTech Rank 1# even beat Noctua NH-D14

http://www.frostytech.com/top5heatsinks.cfm

yooo lingloong, very nice looking and performance as per link provided.

just bring in la...

Fail. two yellow wire? that's going to mess up the fan's RPM reading

Ok ker this cooler? Make sure you are my 1st customer

---

Added on April 15, 2011, 9:12 pmThe Blademaster 120 using 4pin

This one phailed

This post has been edited by lingloong: Apr 15 2011, 09:14 PM

yo lingloong...ya u must bring..comfirm i bought..

Ya I still wait supplier confirmation. Coz got many complain from customer said the Noctua NH-D14 too big and too heavy for the mobo & hard to fix + compatibility issue, possibility to strain is highly occur

Another plus point the Spire will be cost LOWER than Noctua

i mean the Y-splitter, two yellow wire will mess up the fan too, the fan will spin up and down if using certain brand of fan controller.
4 pin pwm will need this http://www.gelidsolutions.com/products/ind...=2&cid=11&id=31

Ya suggested splitter by "taxidoor" for Hyper 212+ is not compatible because it's only 3pin splitter = cannot fit 4pin head. This is what I'm trying to point

The Gelid would be perfect

This post has been edited by lingloong: Apr 15 2011, 10:07 PM

damn..me kenot tahan now

Even I am not using the K series, tried OG genie and I am getting 3.5+ghz but the temp is at 80°C stressed and 60°C idle. Looking for a good cooler replacing my stock. Now I am back to default.

btw, I thought 1st customer deserved getting it for free as a complimentary?

Haha bro if FREE POSTAGE sure can for first 5-10 buyers

linngloong pm me price for u.i wan 1 unit then...

using v design. something similar to cooler master v6 cooler.

Awaiting supplier stock and price confirmation. Once confirm will post up in Garage Sales


The Eclipse II is design like "Batman" logo when look from above. The downside is both of the fan included is 3pin which run @ full speed +/- 2200RPM. Some cannot stand the noise level but perhaps can be settle with fan controller. And it remind me of Venomous-X

For Gemini, look-alike Megahalems Black The design like copy here & there

ya

---

Added on April 26, 2011, 11:51 amdual arctic cooling F12 PWM did not hlp on my cm hyper 212 plus, i compare it with single cm blade master, almost same temp, i not sure is it only me?

This post has been edited by FiragaZ: Apr 26 2011, 11:51 AM

just for fun to day i ran my rig with out any fans in my CM v10. and the results are surprising actually.

the v10 has 3 sets of heatsink. 2 vertical and 1 horizontal. the vertical set of heatsink which contains the peltier element got hot very2 quickly and couldn't be touch at all , while the other 2 was very2 warm to touch.

my cpu temperature on normal with the fans on is around 42 degrees idle. but without the fan it was hovering around 53 degrees.

this was with an amd 955be oced to 4ghz.

i think if i reverse the rear fan to blow on to the bare heatsink and also reset my proc to it's original clock, the v10 could be a very nice fanless cooler.

I dont think two fan push pull is have much difference in temp . I'm using a hyper212+ as well but with two xtraflo . I gt my Q6600 3.1ghz full load at 52C using Tuniq thermal paste .

pwm worst la bro...even normal better than pwm..