use ND version
http://victek.is-a-geek.com/tomato.html

http://cdn.adslzone.net/pub/repos/victek/T...1.23.8513-ND.7z

Before using ND version , make sure you're using a compatible router. Better use the normal version if you want to be safe. Read few posts by victek on how to determine if your hardware can support the ND version !

Yeah, thanks yangxi for the address. Finally flashed it to Victek's mod, but dunno how to use the IP Limiter le. Anyone can guide? Thanks

here.
http://www.easyzonecorp.net/network/view.php?ID=891

---

Added on March 9, 2009, 7:45 pmafter flash new firmware, please clear nvram

This post has been edited by yangxi: Mar 9 2009, 07:45 PM

Hmm, thanks alot. It seems alot better than my old dd-wrt.

how do i configure my LAN-1 port as my WAN port?
My WAN port was killed in yesterday's lightning strike.. Haven't tried to warranty it yet but guess tough luck since they refuse to warranty my Dlink router over the same issue years ago

WRT54GL user with Tomato 1.23 and life is SWEET!!
Followed a QOS template online and tweaked it a bit for my Remote Desktop, VPN & website hosting uses. So far so good, DEFINITELY better than DD-WRT v24 SP1.
Its simpler and though may lack a few functions such as multiple SSIDs and err...what else?
Tomato have something else that DD-WRT don't. Multiple DDNS service logins.
I have DYNDNS & OpenDNS updating both running on TOMATO. DD-WRT only have option to do ONE and i don't think OpenDNS is even an option on DD.

Lastly, love the almost never need to reboot function.
Fast and clean webUI.

DD-WRT's interface sometimes feel like it hates Firefox too. *sigh*.

which Victek firmware should i use to flash my asus wl500gP router? currently its using the standard tomato 1.23 firmware

where you get the ASUS wl500gP ??

http://victek.is-a-geek.com/tomato.html
Tomato RAF 1.23.8513 ND.7z

this router has been with me for 3 years + already got it when it was first introduced ...heh bought it at RM500 back then at c-zone

HI PRO...
i will receipt my new linksys WRT54GL v1.1 tomorrow...
i want to flsh it to third party firmware...
I use for control the bandwidth of ppstream which use at my auntie computer,
i also use the NAS run the bt 24/7...
which version i need to use?
ori tomato ver. OR victet Ver.?

Victek's version - That's for sure

It has more !

which 1 i need to use,got nd or no nd...(my auntie connect to router via wireless)

This post has been edited by jackieng: Mar 27 2009, 09:04 PM

that depends on your core rev of the router. normal version NO ND works fine

wat mean core rev??

---

Added on March 28, 2009, 8:25 pmjust flash my new WRT54GL to new victek tomato.....
now trying setting the QOS...

---

Added on March 28, 2009, 10:52 pmA big question...
How to do the QOS to ppstream?
now playing on9 game very lag...

This post has been edited by jackieng: Mar 28 2009, 10:52 PM

jackieng, already answer you in linksysinfo.org ..

calvin, for sure you have to use the nice Tomato RAF 1.23.8623.2 release, Samba, FTP and printer support is built in

This post has been edited by Victek: Mar 30 2009, 09:28 PM

will try it once I go back to my hometown later.

I installed verseion 1.23.8515 ND version for my WRT54GL1.1 yesterday. (Victek's)
When I did QoS settings I did it so that tcp/udp on the port which I'm bting on gets set to class E.
However for some reason some TCP entries end up as HIGHEST instead of class E.
They're also listed as UNCLASSIFIED(though I believe this is a queue to place them in the correct class.)
The QoS setup I am using only allows NTP and DNS(the default setting) to be HIGHEST.
Any thoughts?
Is Victek around? I would like to hear his say on this matter.
(It seems my corerev was >= 9 so I stuck with the ND version, but the regular versions work fine too last time. Then again I wasn't really using wireless much)
At any rate I hope to get an explanation about this.

Furthermore after disconnecting and reconnecting several times(everyone knows why) it stops responding. Has been like this since v 1.23 victek's.
I have to reboot to get it to work, or reflash.
This one is a persistent issue.


This post has been edited by PSB: Mar 31 2009, 07:01 PM

Can this firmware work on Dlink DSL2640T???
IF yes, can this WSD link with my linksys WRT54GL using DD-WRT firmware???

i also have this issue

---

Added on March 31, 2009, 8:35 pmand i notice this issue started to appear when victek optimize his code

This post has been edited by developer: Mar 31 2009, 08:35 PM