This is the analogy

That the AP allows user to control the output power from 9dbm to 28dbm.

Although the AP capable producing 600mW, it can be tuned down to meet the requirement of the MCMC or any standard set by the sirim.

As an example, although ferarri can drive more than 300km/h, the speed limit is still 110km/h. but you can't stop people from buying ferrari or imported ferrari right?

Those Senao are from local distributor in PJ i am just a reseller, i already email them since you ask so much about papers. Even though you're not buying one at all. Just slamming people here and there.

X tahu lah ape masalah manusia kat dunia nih dengki tahap dewataraya. X ada pasal carik pasal. Ko nak ckp ape pun ko ckplah apa ko punya suka bro, aku rasa aku x buat masalah pun kalau ko x puas hati, . I will not reply any statement from you from now on. End of discussion.

Sesungguhnya dosa memfitnah itu adalah lebih berat dari awan.

Amin


This post has been edited by MX510: May 29 2009, 07:59 PM

Router Worm psyb0t

Written by McMadPete Saturday, 28 March 2009 10:16

In the last days several news blogs were publishing informations about "psyb0t", a worm that infects routers instead of PCs. Often the authors are suggesting that also alternative router firmwares like DD-WRT might be affected. At the current state of our investigation of the issue we can tell that DD-WRT is not vulnerable by default, only when WAN management is enabled there is a chance to attack the router.
As described in the Drone BL Blog the worm works with a brute force attack using dictonary based random passwords - there is nothing we could technically do to prevent that in general. To succeed the worm requires a router whith management access enabled at the WAN port (Web / SSH / Telnet) at the standard(!) TCP/IP ports for the services and a weak administrator password.

To nullify the possiblity to get your router infected by the worm (or to be attacked with a similar mechanism) you can take the following precautions:

* only enable admin access (Administration > Management > Remote Access) at the WAN port when required (most users don't need this and it's disabled by default)
* if you need administration access via the WAN port
o only use services with encrypted password transmission (HTTPS /SSH)
o chose a non-dictionary based secure password
o change the TCP/IP-ports to non-default ports

If a router got infected you cannot access the router anymore via Web or Telnet (SSH only if you did enable it once). As far as we know the worm does not yet install itself resistant so rebooting the router and checking if you can access it again is a first step. After you can access it again please disable WAN access or take the above mentioned precautions. If WAN access is not enabled your router was not infected and the non-accessability had another reason. The last option is resetting the router to factory defaults. Because the WAN port is disabled by default, your router then cannot get infected anymore.

If you have further questions regarding the worms mechanism please refer to the Drone BL Blog. If you have further question please check the forum or contact us.

http://dronebl.org/blog/8

http://dd-wrt.com/dd-wrtv3/contact.html

I don't think that features works on micro version

Because it is not supported

Just get another cheap modem got many ppl sell in forum second hand ADSL modem less than rm100 :-) make sure modem in bridge mode

New Updates Check Out

http://www.dd-wrt.com/shop/catalog/

Yes that's correct

You can try both and experience it :-)

From that you can know which one is better

You also can use rflow to monitor packets

Install a firewall like monowall so u can manage ur network more efficiently, using this setup will totally block the culprit since u only enabled the allowed ports to work 100% effective

Restore to factory default then try again config the ppoe :-) it should works. Use the reset button for 30 seconds

This post has been edited by MX510: Jun 28 2009, 08:41 AM

Use the web flash to revert back to older version v24 sp1 is stable :-)

V24 SP2 Beta for Professional DD-WRT is out :-) much more stable manage to flash my Senao EOC-2610 yesterday :-) running like charm . If u select country Malaysia it will run max 500mW according to MCMC regulations.

ScanArt pls flash it and post ur screenshot here

Install RFLOW

---

Added on July 30, 2009, 12:56 pmNew Builds Update available here

http://www.dd-wrt.com/dd-wrtv2/down.php?pa...7-21-09-r12533/



This post has been edited by MX510: Jul 30 2009, 12:56 PM

I don't think that QOS works nicely with free version of dd-wrt . Try to flash to Tomato :-) if u really need QOS features

Hehehe RTFM bro :-)

I think the wikipedia is already cleared on how to configure it

Sorry if i offended you but sometimes ppl are too lazy to refer to documentation is already listed

http://www.dd-wrt.com/wiki/index.php/Using...fic_Information

Here is the screenshot for noobs

My RFLOW Settings



How to enable RFLOW from your Router



The ip is the ip for the pc u want rflow to send the data :-)

Use of any standard version :-) for full features

Using macro will be lack of features

QOS features for non special edition won't work nicely as special edition version

http://www.dd-wrt.com/wiki/index.php/Supported_Devices