aiyarks.. you guys aaaaa... never read the tutorial sticky ka... go go read it now...

http://forum.lowyat.net/topic/488910

bottom post about lining using line marker...

the marker used in lining, can use eraser to clean, whether it is oil-based or water-based.

but still, no one is answering my question.

even when after it's dried up?

---

Added on December 30, 2008, 8:58 pmer..if IINM, just look at the top of the cap of the marker
if it writes 水性, that means that it is water based. simple!

if it is 油性,that means that it is oil based.

This post has been edited by yellowpika: Dec 30 2008, 08:58 PM

yup, tat's wat i do.

---

Added on December 30, 2008, 9:08 pmhow to put lining on Crossbone Gundam's mouth?

This post has been edited by yshiuan: Dec 30 2008, 09:08 PM

fixed

to yellowpika
im a banana no understand mandarin

almost off topic liao.

I'll ask again, how to put lining on Crossbone Gundam's mouth?

p.s. does anyone here hv crossbone gundam??

Hey,please answer my question,OK.
How to use hobby thinner and retarder mild?

@yshiuan: Me, too, never make any crossbone. Why don't you try washing it? I means the washing panel line skill.

washing? how? having hard time the pu the line oso

http://www.youtube.com/watch?v=FY-1ikkJoQU

This's washing panel line.

if wide surface can use tat technique, the Crossbone's mouth is too small and very hard to hold using forceps.

---

Added on December 30, 2008, 11:30 pmsome review on crossbone. focus on the head part.
http://www.dalong.net/review/mg/m98/m98_i.htm

This post has been edited by yshiuan: Dec 30 2008, 11:30 PM

I don't think that washing can only use one wide surface. Koto kit doesn't always have wide surface, y'know .

Learn your manners before asking lah please. Its like you are demanding for an answer. So uh, no I will not answer your question.

Any Gundam Marker users here? Just wondering lah, how do you know it is going to finish soon? My gold is all watery and well, the gold paint is getting less and less. Time for a change? Thank you for answer yea.

refer here for panel lining.

Link

Or u can try use water base marker juz draw the line and wipe off those excess one with cotton butt or your finger..

if no one reply your question yet..means they got no idea how to reply you and be patient abit and wait for the answer from the pro here la

not start to be rude and start demanding answer to your question like this...people see also when they got the answer for you also they will instantly no more rasa to answer you already

hobby thinner just use like any other thinner la...you just mix it with your paint to thin the thinner...before paint.

retarder are use to slow down the drying process of your paint...usually been use for AB-ing to prevent spider webbing

how to use both of them? both also you need to mix with your paint to use it

and i thought i already explain all these on the starting gunpla pinned thread?

i use the fine tip marker, i tried b4 wipe off using my finger, the result is worse than i thought.
all become black. tat's y i try to ask here.

really no one here hv crossbone gundam X-1 full cloth?

you ask so many times also we all use that way to panel line the mouth... no problem at all... you use wrong pen ka???

not the mustache, the inner part of the mustache, just like the MG F91, got 2 layers one.

try toothpick.
after u draw the marker on the face.use the toothpick to clean excessive ink.
example like u wan2 sharp the line on certain parts, but marker is thick..can use toothpick to clean it.and left a very sharp line.

the toothpick recommended the sharp in edge toothpick.

if still cannot find youtube.
find those modeling video.
they will teach u some sharp lining technique

^tried it
says recommend by him..
good result came out, although the debri of those things still left inside those linings.. dun sweat ur hand when gunplaing.. or else
jeng jeng jeng~