yeah what u give is what u get....performance so so for me
consider to change..

I think there are misconceptions there.

1.The High-K gate dielectric is mainly design for gate leakage control.
( of couse, no doubt amount of transistors are increased as well )
How far the processor can go, it's more likely depend transistor characteristic, amount of transistors, quality and purity of the wafer used etc.
In those old days, Pentium 4s are screw up big time in term of power consumption control, but they have no problem to hit 8GHz
Agreed with that point AMD processors hardly can break through 4GHz region, eventhough they are moving into 45nm fabrication technology

2. Best B3 has no problem to do 3.5GHz above 
http://www.xtremesystems.org/forums/showthread.php?t=183025

3. I would say that 6MB L3 cache can never on par with 6MB unified L2 cache 

4. For F3, 3.6GHz is achievable with air cooling, in the case ambient temperature must be low. 
    Bro @meno has a mighty F3 gem 
    FYI, one of the top 10 guy actually bench 3.9GHz with air cooler
    eldera from beijing , but he bench it in winter season.
    The CPU-Z validation thingy actually is not hard to do so.
    It depends on how good your cooling + how well you can play with clockgen / setfsb + how fast you can save the validation file 

Stupid biostar bios programmer ..Latest TA770 bios  A78XA514.BST make everest cannot read Vdimm , HT link voltage and N/B vcore      Reflash back to A78XA328.BST

Actually 4pin and 8pin is same...the most importand is the rail voltage for 12v2 is how much volt and amphere ...example like tis  11.90v  with 18A

>HT Link Control:

HT Link Width......................... - 16 bit
HT Frequency.......................... - 800 MHz
IH Flow Control Mode.................. - Disabled
HT Link Tristate...................... - Disabled
2x LCLK Mode.......................... - Disabled
Unit Id Clumping...................... - Disabled
>CPU Feature:

NPT Fid Control....................... - x10
Virtualization........................ - Enabled
AMD K8 Cool&Quiet Control............. - Disabled

>DRAM Configuration:

MCT Memory Timing.................... - Manual
Maximum Latency...................... - 8ns
2T Mode.............................. - Auto
Cas Latency Time..................... - 5
Pre Charge Delay (tRAS).............. - 12
DRAM RAS# Precharge.................. - 5
DRAN RAS# to CAS# Delay.............. - 5
Bank to Bank Cmd (TRRD).............. - Auto
DRAM RAS# to CAS# Delay.............. - Auto
TRTP................................. - Auto
Write Recovery (TWR)................. - Auto
Write-Read Command (TWTR)............ - Auto
TRFC0................................ - Auto
TRFC1................................ - Auto
TRFC2................................ - Auto
TRFC3................................ - Auto
Trdrd................................ - Auto
TrwtT0............................... - Auto
Twrrd................................ - Auto
Twrwr................................ - Auto
CS/ODT Pin Fine Delay................ - Enabled
Bank Swizzle Mode.................... - Enabled
Auto Tweak Performance............... - Enabled
Optimal Performance Mode............. - Enabled

>PWM Settings:

PWM Control.......................... - Enabled
CPU VID Control...................... - 1.40625v
CPU Vid Special Add.................. - Auto
CPU NB Vlotage Control............... - Auto
CPU NB Vid Special Add............... - Auto
DRAM Voltage Control................. - 2.12v
SB PLL 1.2V Voltage.................. - 1.20v
NB Core Voltage...................... - 1.20v
NB PCI-E Voltage..................... - 1.250v
NB HT Voltage........................ - 1.20v

Genie BIOS Settings:

Spread Spectrum................ - Disabled
CPU Host/HTT Clock................... - 340MHZ
CPU Host/HTT Boot Up Clock.............. - 280MHZ
CPU Host/HTT Adjust Gap..................... - 5
PCI-E Clock.................... - 100MHZ
[/code]

Example wad inside the Bios ! 

i think i nid to bring my laptop upstairs ... ==" using 1 computer is pain in da ass ...

clear cmos, it could be d system can't take d overclocked speed. 

try to boot w/ one stick 1st. then save optimized settings & check how things go...