whe........... finally V3.0 lor........ let spam with some pictures on the 1st page.....

my old faithful plain jane........



Added with some el wires.....





the mobo tray with component on,


Tray slide in casing.....



try to bling it up with old ccfl i found in my junk......

but turn out not nice though ...... .. not my cup of tea





Finally got a 4gb tracer kit install, super bling lor......





ok that all folks.....

uncle ho, mana cosmo?? CM main attraction for 2007 & 8 wor..........

RahXeph0n, good work there........ nothing wrong with the ide though, i like it some how hehe............

may be time to add more bling bling stuff to ur casing ?? and 1 more fan for ur hyper tx would be a good idea

RahXeph0n since u using 4 pin only, buy an extension in lowyat....... makes easy life for u, and u dun need to buy the expensive silverstone 1, there are others just look around

very difficult i said, u need to cut the rear panel out and revert it......

lichyetan, what u hidding underneath the shield ? ur 2nd rad ?

boyz how heavy is ur mobile gaming rig hehe...........just wanted to know....

lichyetan, i notice u change ur mobo too hehe, mana itu transpiper ?? Btw speaking of chrome sticker, it wont last u long. May be u can try flash tapes, it have some sound dentening effects too but it a hassle to remove later on though hehe

it not easy to find 80x80x15mm fan around here ......

clawhammer i remember thundermatch got some, but not sure ada stock lagi tak.......btw if u really want cheap fan, uglyvamp have some cleareance now, u can go to his thread

it being a while for good old skool stacker to show up hehe.........

post more picture when the hardware are installed........i will post mine 830 once got my hands on the new hardware

guys some new item from CM, looks promising although most of the previous water cooling kit from CM is really a joke,

The cpu block looks like a D-tek fusion design, but interior i have no idea though. CM Claim a 600 watt thermal dissipation, this may give some hint how the performance go

http://www.sundialmicro.com/cooler_master_..._1741_1334.html

source from VRzone forum

DaRkSyThE, which cosmo u getting ?? thermal right city........ should be another nice piece of heat pipe madness.........

may be u can put some thick delta inside hehe,

cosmo S is still not up to the mark of the old stacker, not enough bays, slightly short on the height.......

DaRkSyThE , auras eh, hehe........ u should call it heat pipe city instead lol. Normal Cosmo, even more reason for u to put in Deltas hehe, heard that the cosmo can silencer it down even @ max

eh sorry bubuchai, i tot someone already reply u hehe..........

i think u should ditch ur led in ur uv led fan, spoiled the look a bit and get 1 more fan for ur hyperTX, 2 fans look better and perform better too

the rest very nice, like ur sleeves.

LL 1 is very thin, the original praetorian 1 is quite thick iianm......

well actually with push pull fan u get a better performance on ur hyper TX, a higher pressure to push through as the fins are closely stack.

then let ur rear fan suck air from other place to improve cooling over the mobo side....

got not showing pictures only.......... haha

pikacu, how did u make ur Graphic card glowing, does not seems like UV effect

eheh i must insist, i demand picture, fugly or not, we dun have pictures here........... very sien ler

ic CM also goin single rail haha...... good news, but why so little connector, dissapointed.

btw who is the manufacturer for this psu ??

kltower4 , i see you got ur eliminator in service already, where is the side panel ? u throw it away ??

long time never load pictures up here already............

recently got some major upgrade on cooling system. so early pictures.......



Hehe no need to explain......



installed on the mobo tray........ luckly i got a tray , easy for me to install this little giant

Shot in operation


Some teaser.....

myke, go check Coolit Eliminator.....

OC4/3, now i'm running 1.5v already hehe..... temp still quite ok load around 70. but idle very good, can go 27oC even at 1.5v

to go 1.6, i think i need to mod the eliminator to do the job already, it seems the water volume is too small, dun have enough capacitance. i would need a reservoir and a radiator.

chyu89, consider very bad already the quality. It lumix.... need a more sturdy hand to take picture