how much vcore you need to get that 3.4?

owh my bad didn't thought it'd give much effect will try again later

same here. that's why i thought it's okay to try stressing+doing some other things at the same time, to make sure it's 100% stable..
i think might be better if i increase to 1.4

btw, i got a question.. last night i tried 3.4GHz at vcore 1.53 to 1.65, but i can't pass the windows loading. it'll go blue screen or just stuck..
ram divider 400, vdimm 2.05, and the refresh cycle timing all at 195ns..
very2 confused what's wrong till 1.65 can't even boot

This post has been edited by muh_is: Apr 10 2008, 01:50 AM

I think reached my limit edi.. can't go any further even at 1.72 vcore with ram400 5-5-5-15 at 2.05
temp maintain at 45+ during boot, but can't pass the windows load.
this one can't go stable orthos more than 10 minutes.. i dun think it's my ram, cause my ram can go higher than this and stable +8hours

well, i did tried at 1.5,1.53,1.56,1.58,1.60,1.62,1.64, till 1.7..
and cannot boot.. that's why i think i'm at the limit.. maybe my mobo 3.33 can't even stable more then few minutes orthos at 1.56.. load temp is bout 45-50..

what's the highest u got?

330HT at 1.56Vcore kinda too high i think..

what vcore did you get at 3.4?

This post has been edited by muh_is: Apr 10 2008, 08:02 PM

owh really btw, started to get confused, might be off topic
which one is performance wise, 2GB ram which could be oc higher, or 4gb ram? ballistix 4g kit and team extreem 2gb in my mind rite now

biostar TA770 got 8pin

which batch is your F3? V3? good results there

lol actually was jealous cos mine have to go 1.56+vcore to be able to boot at 3.33GHz

for me, using the jumper kinda irritating since the position of TA770's jumper is right beneath the gc.. so if u're using those high-end gc which is longer, kinda hard to reach the jumper

lol maybe will sell, if i can raise enought money for dfi mobo

hhahaha.. aiming for DFI will always remain a draem well, senior2ku uses high-end gc and all. i'm not much in gaming.. so.. nah.

Just received my ballistix, and my housemate gave me a try with his brand new AX78
same proc, psu, cooler, hdd, rams only the mobo change


this is my proc limit i think.. can't go any higher


this one using my TA770, can only boot to 338X10 once, then can't load windows anymore


i think both mobo rocks

This post has been edited by muh_is: Apr 22 2008, 12:34 PM

lol just edited ah? using 667 lor.. cpu/6

mal to 10 ar? will try later btw, yours at 3.4 stable r? for 24/7?

what bios are u using? older bios (dun remember which one) will automatically push ur multiplier back to the nearest+lower *.5 if u choose the one without *.5..
i suggest you update ur bios to A78XA125.BST, or the latest, A78XA328.BST it's better+more stable than that one

FINALLY! a 24 second even though it's just below 25s by 0.1



24.985s | x2 3800+ F3 | muh_is | 3367MHz 337x10 | Biostar TA770 A2+ | 2x2GBCrucial Ballistix | 1122Mhz @ 5-5-5-14-2T | Tuniq Tower 120

This post has been edited by muh_is: Apr 22 2008, 12:40 PM

32MB entry


22m 19.750s | X2 3800 F3 | 3315MHz | muh_is | Biostar TA690 A2+l | 2x2GB Crucial Ballistix | 1104 | 5-5-5-15-2T | Tuniq Tower 120

edit: ops, double post pula thought it's still going to combine with previous post

This post has been edited by muh_is: Apr 22 2008, 02:00 PM

i think it's better to keep it around 1000+-.. HTLink = HT multiplier X Bus speed

This post has been edited by muh_is: Apr 22 2008, 07:40 PM