Or mine is maybe exceptionally bad using stock vcore on 2.8 now daily...I am happy enough thow... Anyone here tried ballistix tracer 667 2GB more than 1000mhz? me kinda scared to try...this my younger brother's ram...Max i tried is 950mhz with loose timings 5-5-5-15....

not hardcore but just... dun wanna say the word la.. ppl only do 1.8V on LN2 or DICE, maybe peltier too.. but this.. is too much.

From what I've seen.. It may not be accurate..

All those with 16s+ is using Crucial Ballistix Tracer..

Mine running at 3600Mhz but 17s+.. 

@Amedion
Can mod eh???   Gud2... I'll go n check out in Google... But surely its dangerous 2 mod it rite??? I mean if wrongly done afraid it might KABOOM     N using DICE??? Aiyoo... I pokai later on...  

@Silverfire
Cooling is da problem dat causes voltage drop izzit???  
Ok laa... comparing wit my cheap water cooling set, of course air cooling is better.... Unless if I upgrade my WC parts wit a better 1...

My mobo NB voltage is 1.25v.... when must increase ar???

@big sifu a1098113
how bout my deduction of de strappy thing for higher multiplier?...
i can get more den 388Mhz n i dare not raise more then 1.5V
any ideas to pass on to me?...
(dun tell me get new proc la...keke...no $$$)

another thing is about rams...
i now eyeing either teem extreme 800mhz (rm255) and crucial ballistix 1066Mhz (rm 295), both also 2*1Gb kit n also microns IC, which 1 do u recommend?
n i might also be getting e8200 or other 8x/9x multi CPU
i dun1 2*2Gb yet cos i'll get CF 3870 soon, which mean i would even lesser den 3Gb of rams s i wouldn't embrace 64bit yet

---

Added on April 20, 2008, 10:24 am
yo...de mars is fantastic...1.8v for kvr to go 890mhz
jus sad that my high multi CPU scale not that good
n de KVR got 2 rev. E chip among the other rev. A chip...
   

thats right.. but will take a whole lot of time.. 

NB temp doesn't change much at load i think,
not sure as i never observe b4.
yaya naked pc , thanks for the pic anyway

Go stepping e2140 is china batch.hehe...db sure get it from china...SLALS stepping.....
should buld e2140 GO from chiba db brother....i just dunno how to pay them.erm..........anyway 1.2xxV should no problem at 3.6Ghz orthos.and it is 6750 base cpu.u can unlock L2 with mod.4MB L2 at E2140 Go Stepping.db u know tat???

BTW, OT here: Can someone teach me how to properly clear an abit IP35-E CMOS and boot it again? Mine couldn't POST

Take it back to old skool..    OR u can try like mine... Put jumper to clear cmos.. then off the psu till no led watsoever light on board.. then turn back on and put back the jumper to default.. 

almost sub 15s for super pi 1M 
prediction was right, the heat is bottlenecking the oc previously
use chilled water cooling, able to push a bit more only,
this baby is so hard to serve 
best try so far, 15.281s
[attachmentid=459679]

cpu-z validation: http://valid.x86-secret.com/show_oc.php?id=355388

To be honest, the amount of Vcore needed is relatively high for 4Ghz and I used to have an IP35-PRO which I think it has some weird problems at high FSB too. First of all, did you try running 7 x 500 to see if it works? If your board doesn't do 7 x 500, it means 500FSB is not possible.

The CPUz Vcore reading isnt accurate, I'm getting about 0.04 of Vdroop...set 1.54 in bios but on load i'm only getting 1.50V. should i change my mobo?

errrrmm

not sure ar....

even i OCed my E2140 3.5ghz on stock daily using TTBTVX the temp on the bios and mobo sensor is 29c ~ 31c...and in core temp is 38c~40c..
on stock HSF im not to sure....maybe need a decent HSF....

and guys...i OCed my E2140 at 3.5ghz using 438 x8..its stable..can orthos more then 2 hour and run superPi 32m...even play game stable...
but when i turn off my PC and switch off the main power...leave the machine for a while and turn back on sometime it cant boot...sometimes got beeping sound...sometimes it display "Bios boot block, please insert disk in drive A: "

pening already with this setting....update the bios to the latest one v17 also the problem occur...is my ip35e reach the FSB limit?

so the FSB wall is from the mobo ar?

have u try save that OC setting and shut down your PC then completely discharge the electricity from ur machine and try on it back?
i got this 3 random prob when i shut down my machine and discharge the power....

Tried DI oc on G0 E2140 yesterday,
best pi result so far, 14.875s,
[attachmentid=483264]

CPU-Z Validation: http://valid.x86-secret.com/show_oc.php?id=367764

boot up on 3.6GHz, then top up by using setfsb
check the temperature, 7C under DI cooling 
This G0 is heat monster , at 1.8v temperature is 60C with DI cooling

best shot, 500 x8 on E2140 
http://valid.x86-secret.com/show_oc.php?id=367765

[attachmentid=483265]
Thanks to J.J for benching with me in this dry ice session