My setting are below

i raise my mhz from 166 >192 means 1.83gig(original)>2.13ghz

and i also increase my cpu Vcore from 1.65>1.675

.

Thats all i did, need consultation on what should i set next.

cooling method i have a casing sized flat-type table fan blowing.

currently my cpu temp is 52C (refer to HardwareMonitor)

if i on cpuidle, temp will go down to 46-48C.

Ur help will be much appreciated

Continue to increase the FSB and voltages accordingly until you max out the OC? Is this what you're asking?

Yeah u can do that, or play with the ram timing.

i duno how to play with timing

ya, and what setting need to be set to increase the speed? How to set ram timing o?

This post has been edited by chyu89: Feb 21 2008, 01:10 AM

For those Bartons, FSB should make more sense than optimizing the timings.

i'm using abit nf7s mobo. theres setting to 3200+ . i set the vcore to 1.7V then fsb to 200mhz. RAM i set it aggresive mode.theres turbo mode but not stable. I think thats the best my rig can do

1.7V kinda high there

This post has been edited by bulibulizaimon: Feb 21 2008, 02:22 AM

It's not high at all Back then, the default Vcore is 1.65V

---

Added on February 21, 2008, 2:26 amSet your FSB to 205 and increase Vcore by a notch. You might also want to read some overclocking guide and have an idea what is it about

This post has been edited by clawhammer: Feb 21 2008, 02:26 AM

With setting i shown last come up with blue screen. Give up hardclocking. just reduce to my previous OC setting 192mhz 1.675V. thanks for the guides and opinions. peace out

ceh, so fast give up OC, we guys always play with blue screen. You one or two bluescreen want to give up. What la. No fun!

U also retired liao ma.. i havent got enough budget for new rig leh. I lose this rig, i lose everything. I'll keep on research . Mayb not experimental type lol

My last barton 2600+ AQUCA max OC hit 2.57Ghz..
Daily use 2.3Ghz..Using ABIT NF7 Rev 2.0

bro, i only have one rig too. And if i lose my rig, i dont have anything. But whats an OC without a risk. thats why, when it works, its an awesome feeling

the feeling was awesome. especially when it success

alert

wow .. those boobs really arrrr

ya .. what an oc without risk ...
i dont think you will get ur rig burnt out if you monitor carefully its reading (if any .. )

when u got there ... the satisfaction is soo high (comparable to sex & jerking off .. choose which one)

last time my locked-barton did 2.4g@1.85vcore,stablely running after 24 hours priming.hehe,dat was when im still studying:) in college.past story la..but today no more ler:).play around wif timing & alwiz monitor d temp bro cuz d proc itself got default voltage high already

This post has been edited by greactor: Feb 23 2008, 09:39 PM

1.7 is low...
I've seen people pumping all the way to 2.0v for Bartons, but it is not very highly advisable to do that for the long run.

Wat are the specs of your rams?
If possible, try tweaking all the setttings yourself rather than relying on the mobo to overclock your rams.
If you're running DDR400 rams, u might wanna set ur rams to run at 166 and start from there, running 1:1 is always more result yielding than any ratios.
Btw, what cooler are you running? Try to get something like an Si-97 at least. You should see an idle temperature in the high 30s or low 40s and a load temp below 50.
Try to pump in extra voltage and move up gradually, if you're not very confident in the voltage thingy, try to limit it within 1.75 and see whats the max you can get from it. Abit boards have a tendency to overvolt...