Muahahahaa...still under 60 degree ma.
Using back 3200MHz already. Fed up..   

-pWs-

Highest is 1.425v   
Dun wan add more Vdimm already since already 2.2v   
Any idea??

-pWs-

please don't just simply say something without evidence
i dunno what's wrong with you,
you seem love to flame biostar for no reason
if you are not sure of something,
you can always google 1st 

@ongbs
If my PWM area nvr cool by HS and fan, will it be a problem??
Thanks

[attachmentid=370663]

-pWs-

maybe MSI's R&D  is fully concentrate on intel platform development , no time for AMD 
anyway all the best to bro AoiNatsume , hope he solve the problem somehow. 
IMHO, if use water cooling + ice , most probably oc will stop at 1.7v
( Tried to pump 1.8vcore b4, cannot raise the clock speed also due to the temp )
1.67v is around 1.7v ....  shouldn't make a big gap 

sorry bro pws, me just free to online now
will attach my screeny soon ...

---

Added on January 3, 2008, 12:41 am
PWS,
seems like bro CV aldy answered yr question 
ya, if using WC becareful on the PWM side, especially when running orthos.

If my memory serve me right, u told me b4 u RMA yr mobo twicw due to Orthos right?

My DFI rig was busy running Orthos@ 3.4G, 1.575Vcore for whole afternoon...
refer CPU-Z for my setting....will let u know why I added the heatsinks
Pls refer to your mobo pic, I highlighted the PWM MOSFET where I attached my digital thermal probe.
I am running WC, with my setting as shows by CPU-Z.

(Ambient temp around 26C in air-cond room, my rig is put outside of casing, ventilation is better than opened case)
All my PWM MOSFETs got small copper heatsinks on it, without top 120mm fan running, the Idling temp around 50C+.
Once running orthos, around 10 mins later the MOSFETs temp will shoot up >90C.
Keep in mind that PCB is quite good at heat transfer (due to the copper trace, especially on the packed PWM side, thicker trace found due to high current load)
Those 90C+ heat will transfer to surrounding components (mostly via convection I believe), so think by yourself what is the CAPs temp look like?

At this time those heatsinks I stuck on top of CAPs, temp >65C cos I can't even rest my hand on it >10 sec!!!
Well, I think it is time to turn on my 120mm fans on top of PWM circuit....

Within 1 min my temp measuring point drop to <60C 
Those heatsinks on top of CAPs <40C.

So conclusion is I will never run orthos test >1hr without extra cooling 
Although those electrolyte CAPs are designed to stand around 100C, judge your self will the lifespan of mobo drop without extra cooling?

Heatsinks might not be necessary but extra fan to me is a MUST when running Orthos >1hr.

Hmm...time to stop my Orthos now and check how is the temp look like 
After 2 mins the temp measured below 40C with the 120mm fan running  

I treated my mobo nicely with extra cooling since Socket A platform and me used > 4 mobos for the last 5 yrs (3 mobo were Abit NF7-S V2.0).
2 of the NF7 kong due to stupid lighting kissed my mobo via LAN/ phone line. The other mobos still working till recently I sold it off) 

OK, time to surf Garage Sales..... 

Just work hard not enough bro, ball must be big to pump Vcore + Vdimm kaw2   
Some more taruh iced water cool 

Without iced cool I doubt that any of the F3 users here can drag u down from 2nd place 

batch / steppin is d key... 

guys, when fsb > 300, do you guys increase d htt / nb voltage? 

new updates...

any comment guys? how much voltage u guys pumped in order to be prime stable @ 3.2GHz? 

i think my chip not so impressive, 3.2GHz need quite high voltage, so at d moment i'll just focus on bringin down d voltage by burn in d chip... 

[attachmentid=372708]

Hi guys,

I just setup the F3 with the DFI NF Ultra M2 yesterday with D9gmh 512x2. Can I know is the stock bios good to use to oc it ? I set the vcore to "default" and 1.8V for the ram, DDR533, 250 x 10, FSB ratio 4, no prob to boot up to 2.5GHz, 1000 HT and 625MHz for ram at 4-4-4-12-1T.

But, if i go above 250fsb, it can't boot up even though i change the fsb ratio to x3. Need more vcore ? May I know whats the default value ? Should i set to 1.200V or higher ?

Bro -pws- and CV6149: same board as u guys, what to do next to get 3.1ghz ? Using TT V1, temp in Everest is 33C on each core.

CV6149:  this is the burnt mobo lo, hehehe, manage to replace the diode. Testing it out b4 try out on the abit NF-M2 nView.

Please help to guide noob guys. 

Will upload SS tonite, its at home now. idling.

Which one??

-pWs-

psu is atrix 500t. later i try that timing n let u noe the result.

how do u know it's not good? supplier already test one by one? 

About biostar i saw several previous user said there is some bios problem, izit?
what is the problem?

how about gigabyte GA-MA770-DS3? good?