make it to BTX
put 2 high airflow maybe silverstone product fan
its 110CFM ++ if im not mistaken
put on some bling2
make hole for acrylic at top n side panel
den it would be okay edi
nice but good

can you post some constructive comments?
The case already BTX lol
btw, TS, go here to see a great mod done on V600

woahh cute casing u got there, really

admire it

btw, have u installed ur setup inside?
care to show some photo?

I don't see any place suitable for the psu to be. Maybe just plan the airflow of the proc's hsf with the psu fan by adding a duct. Instead of hot air blowing on proc, the psu will suck the hsf's hot air and blow it out of casing.
As for ianho's mod you've mentioned, it's not the psu's held by acrylic. It was placed at the front, connected to the back.
As long as you don't touch anything which supports the case, the case will still be as strong as before.

As for the top panel, cutting a window will not cause the whole casing to no be strong. Just don't overdo it like cutting to the edge. Otherwise, you'll have a lousy top panel.

Side panel... I've got not much of an idea. Because I think that the psu and the stock fan is blocking all the view. Unless you wanna look at ur nice HDD and a little bit of every other thing, a window wouldn't hurt the casing structure.

acrylic can be break easily ma...so the thief no need to open ur sidepanel also can steal hardware from ur rig...

so maybe no need side window for ur case....

as for the PSU placement, maybe can do like uncle ianho done b4...

Acrylic where can break easily 1?  A window with standard industrial grade A acrylic securely mounted to a side panel, is very difficult to break. The windows that r easy to break are those cheap rm150 cases. Coz the cheap cases dont use acrylic, they use cheap transparent plastic which is easy to crack.

First: HDD Bay



got 8 screw (4 on the bottom & 4 on the top), unscrew them

change the position of the hdd bay to side way (rotate 90° anti-clockwise)--> less air restriction

1 con if u this way:

every time wanna remove the hdd, u gotta unscrew the 8 screw first..

take the hdd bay out or rotate it to its original position

only by then u able to remove the hdd from it's bay

reason: the mobo blocking, not enough room to take out the hdd

that's why u need to rotate to its original position first, really hassle la

who cares, it's not like we gonna remove the hdd everyday

Second: PSU



change the psu the other way round la

let the psu exhaust all the hot air trap there

seriously, u don't need the fresh air intake for ur psu la
Third: Graphic Card Area



Intake Fan = Side fan
Exhaust Fan = Blow hole on top, either 1x120mm or 2x120mm, up to you

ur GC temp will drop drastically  
Forth: Cable Management

the excessive front i/o cable:
buy a cable tie + cable tie base
tie the excessive cable length on the case ceiling

the psu cable:
well, if u change the position of the psu, the cables will be at the down side right
do it like front i/o cable --> tie it to the case floor

if u let it hanging like that --> restrict air flow
mind answering me, what cooler u use for ur proc?

btw, i tried all the steps above in my V600

temp drop like

>>>>orait bro will rotate it around<<<<<

i like this quote! sound so simpe, gud luck!

make the side fan as intake fan, that way fresh air goes in from the side panel, hot air goes out though the top panel

u don't wanna to circulate the hot air back into the case

making the top panel fan as intake, exhausted through the side panel, hot air goes out & up --> suck in again by the top panel fan
dunno, can't comment, never tried it before

coz already found the solution (without modding heavily --> just blow hole on top)