currently, i stick it to windscreen in the car with masking tape holding it in place (at adhesive side), work perfectly.

if i use back the original adhesive, meaning turn it the other way round, will this still work?

Yes

No

50/50

Maybe

OK

Don't know, never try. Ask tng.

Unless your car can turn turtle. Yes will work.

as long as you don't add on extra tint on your windshield later - it should work.

This post has been edited by pokchik: Nov 28 2025, 08:50 PM

Mine work as it should.

Logically it should. But somehow I feel something will go wrong.

Some ppl say stick behind number plate is easier to detect wor....

why people don't stick inside of their car is because of their tint

as long as the part where you stick it doesn't have tint obstructing it, it should work

Yup... some tint block everything.

Can always try first before permanently sticking it.

yea group member all stick at car plates with zero error

If you turn it the other way around, the toll pays you instead.

Toll operators hate this trick.

Hang mirror behind rfid. Can enchance signal.

Tumpang.

Can we duplicate RFID sticker?

ok, i will reverse it and see how.

i tried different locations, that why i use masking tape. and found the best position.

but it dropped off few days ago. i want to make it fixed this time.

Ayam aruz also stick inside, with tape

best place is back of car plate, never fail

you use original adhesive?

good to know that.
but any tag stays outside will not last long.

Can use acrylic base + suction cup too. On my other car, it works well too.

my rfid stucked outside surface windscreen since beginning of rfid till now no problem

In other countries, service providers adapt for consumers. However, in this country, service provider insist consumers to adapt for service provider.

rfid stick inside windscreen work just fine except those with metallic tint.

long meant for decades oh

9/10 RFID unable to detect on highway due to people innovation to stick the tag in location that hard to scan .. not to mention different toll tend to buy different scanner and install with different standard … so when it works in one toll may not on others …

I was one of the early adopter my rfid sticked by the tng agent, no issue using RFID till today, when TnG started to go live and let people stick their own, thats when all the reverse forward issue happening …

Good technology X Dumb People = Dumb Technology

this is for you...when you think a company is all for consumer in their heart.

Ayam pilot rfid installed by tng agent, always failed
Especially at mex cheras

Then i install my self at aruz, in cabin, use tape, only once fail at spe

Get the acrylic mount. When you repeat the stick and peal the rfrid strip can "break"

My personal experience, it works but less sensitive. Means you need to get closer to the RFID sensor by few feet for it to detect the RFID tag.

For maximum performance, sticker side have to face into car cabin.

What I do is use the roadtax sticker holder, put in the RFID tag(sticker side facing car cabin), then attach to the windscreen. I did cut the roadtax sticker to smaller size(couple of CM bigger than the RFID tag) and attach it to the top middle part of the windscreen. Has been working perfectly since then.

BTW

i think what you mention is true but also some cars might have another rfid for their taman/condo/car park
that other rfid , i belip, might cause problems at the toll gate, correct me if i'm wrong

This post has been edited by tahfeikei: Nov 29 2025, 01:23 PM

in case you missed it, the original adhesive is still virgin.

not for my case, i put my company rfid at upper side of tng rfid, no problem for both scanning.

mmhhh....speaking of this, i'm not really sure my company rfid recommended pasting is at outside or inside of cabin.
if it is outside, basically, i have proven the tag is actually sideless.

i was thinking to use this, but i'm rather lazy, lol

My RFID is the first-gen ones during the trial phase, square tag.. i dunno why but it seems now like the tag cannot even be detected on almost all tolls..

Stick on the back of car plate the sensor can detect meh?

Well not really. It is actually the dumb operators who install the sensors differently, not standardised at all.

I am also an early adopter - mine was the firt gen rfid, installed by TnG themselves..

mine is at upper left corner behind 3 layers
- the tint (non-metallic)
- the dark band tint (non-metallic)
- the clear plastic for stick old roadtax on one. i stick the RFID instead.

- finally the entire thing is held the sticker that hold old roadtax

I stick like this, so far never fail



I also got the first-gen tag, the white one stick inside windscreen
it fell apart last year, quite literally turn into dust
then I changed car

Just get the RFID sticker holder. No issue also