could be working on new TV package

TM seems very confident. Must be good gift.

What are the models of the freebie mesh wifi given by TM currently?
1. Zyxel EX3220-T0
2. DLink DIR-X3060Z
3. DLink DIR-X1860Z
3. Fiberhome SR1041F
4. TPLink - TM don't give TPLink for wifi6 right?

Pls correct if wrong.

Thank you boss. You’re on 2Gbps? What’s your solution now to overcome the 1Gbps limit?

You are not using Gpon bridge mode right? Just Gpon router mode,and plug 2 lan cable Router to ONR?

I remember. At least last time can see in unifi portal the "Promo Discount Perpetual" or "24 mths" so can keep track and report to TM if not correct. Now cannot see already.

M9 Plus' RJ45 is cacat crippled OKU. It can get just above 500Mbps, so it won't disappoint - until you go for higher speed.

I was disappointed with it when I upgraded to 1Gbps.
Went only and read complaints of users who were also surprised that its RJ45 isn't true 1Gbps.

Found this out since May.
Post #1521 (since i can't tag in an-already multi-quotes post)

I dunno why the AX201 on my MSI board is so slow. Tried upgraded firmware and drivers a few times then left it at that since I don't use the wifi. Maybe one day will try to find a solution.
https://forum.lowyat.net/topic/5297330

I have check and verify to a person, TM NGN Fiber will show Generic OLT (No OLT ID shown) like this OltVendorId: 0x00 or Other (20202020) (OpenWRT PON Stick), that OLT is XGPON upgrade-able

The NGN show 0x00 should be Huawei

For Nokia, didn't offer XGPON to TM, only XGSPON and above:
[attachmentid=11483250]

Both require Universal License, Huawei/Nokia charge TM a expensive to support Universal. What I have been told.

Can check if your fiber line is connected to NGN or not:

xPON ONU SFP WebGUI


D-Link DPN-FX3060V
1. Enable Telnet
2. Putty to D-Link 192.160.0.1
3. Type: sh (into root)
4. Type: omcicli mib get 131
5. Output should be show like this

Here list common MIB Id if you want to check:

Managed entity ID	Managed entity	Description G.984	Clause G.984	Clause G.988	AT&T Open OMCI	Verizon Open OMCI	Required/optional G.984	Mandatory G.987, G.9807.1	Mandatory G.989	Mandatory G.986	Mandatory IEEE 802.3, 802.3av
6	Circuit pack	Used for a plug-in circuit pack module. Can also represent a virtual circuit pack to distinguish types of ports in an integrated ONT	9.1.6	9.1.6	5.1.6	M	CR
7	Software image	Used for the software image of the ONT or its components that contain independently manageable software	9.1.4	9.1.4	5.1.4	M	R	M	M		M
11	Physical path termination point Ethernet UNI	Used for physical path termination point at the Ethernet UNI	9.5.1	9.5.1	5.5.1	M	CR			M
84	VLAN tagging filter data	Used for VLAN tagging	9.3.11	9.3.11	5.3.4	M	O
131	OLT-G	Used for OLT identification for interoperability facilitation	9.12.2	9.12.2	5.12.2	M	O
171	Extended VLAN tagging operation configuration data	Contains configuration parameters for enhanced VLAN operations, including adding, removing and changing multiple tags	9.3.13	9.3.13	5.3.5	M	CR
172-239	Reserved for futuremanaged entities
240-255	Reserved for vendor-specific managed entities
256	ONU-G (NOTE – Inthis was called ONT-G)	Used for ONT equipment management	9.1.1	9.1.2	5.1.1	M	R	M	M		M
257	ONU2-G (NOTE – Inthis was called ONT2-G)	Used for ONT equipment management	9.1.2	9.1.1	5.1.2	M	R	M	M		M
262	T-CONT	Used for DBA	9.2.2	9.2.2	5.2.2	M	R	M	M		M
264	UNI-G	Used for user network interface for GEM service	9.12.1	9.12.1	5.12.1	M	CR
277	Priority queue (NOTE – Inthis was called Priority queue-G)	Used for ONTs that support priority queues to multiplex ATM or GEM traffic flows	9.11.1	9.2.10	5.2.8		CR
329	Virtual Ethernet interface point		n/a	9.5.5	5.5.3
350-399	Reserved for vendor-specific use
453-65279	Reserved for future standardization
65280-65535	Reserved for vendor-specific use

Any screenshots? As far as I’m aware, there isn’t any difference. I have a Z Fold 3 as well and it’s doing the same/similar results

Z Fold 3 is by no end the most high end android device but FastConnect 6900 in the Snapdragon 888 is already capable on reaching 3.6Gbps

Yes, I am aware that 160Mhz is not supported by iPhones , my AP currently is running in 160Mhz mode at the moment

Considering that most of the time I have LOS it's certainly not the expected performance but it'll work I guess. Only saw it hit beyond 1Gbps on WiFi on the ONR itself when it's being installed and never after that
Hm interesting, what phone is it? And is this on SFP GPON ONU?