haha , about hdd problem after overclock , i kena before too .
always have to enter password twice ( welcome page login ) .

if you got it from the 2nd f3 bulk...then u can use stock vcore till 3.1g....as promised by our bro

this depends on mobo too....some mobo can't do 3GHz at stock Vcore.
My DFI mobo is one of the example

The same F3 running fine at 3GHz 1.25V with my previous Abit AN9 32X but my DFI need min 1.4V.

wahaha, congratulation bro~!
marching to 22sec next

btw, just checked the pi 1M thread, adi 8 F3 guys in top 10

http://forum.lowyat.net/topic/321443

edited: bro xixo , try to use memset 3.3 , this memset 3.4 beta sucks for am2 ram tweaking

This post has been edited by dblooi: Dec 16 2007, 02:47 PM

i should listed there too .. =)

i must oc more...kick andre

oh ya...690g ram voltage can reach 2.6v?

haha, andre is pro OCER from indo , he's using cascade phase change cooling
the am2 result he bench it long time ago
btw, ya TA690G can add till 2.6v

Sorry~~im still newbie here ~~ can i ask that which software is good to use as monitoring cpu temperature n fan speed ??
thx~~

Go for Lavalsy Everest

-pWs-

wanna ask that which one better ?
AMD5200+ 2.6Ghz L2@1024 X2 90nm Sol windsor VS AMD 5200+2.7Ghz L2@512X2 60 nm SOL brisbane

This post has been edited by kellefe: Dec 16 2007, 06:10 PM

Selling my brisbane, good and stable proc:
http://forum.lowyat.net/index.php?act=ST&f=54&t=592250.

AMD5200+ 2.6Ghz L2@1024 X2 90nm Sol windsor

I think this will be better.

in term of performances ? brisbane only win in term of heating right ?
brisbane is using G2 stepping~~ and windsor is using F3 steeping~~ any opinion on this ?

Brisbane
pro : 65nm SOl, higher speed
cons : L2 @512 X2 , G2 Stepping

Windsor
Pro : L2@1024 X 2 , F3 Stepping
cons : 90nm SOL

This post has been edited by kellefe: Dec 16 2007, 07:34 PM

My meager overclock at stock everything.




This post has been edited by redken: Dec 16 2007, 07:52 PM

Windsor F3 is easier to OC, but takes up far more power and puts out more heat than Brisbane G2. Both will reach 3.2-3.3Ghz at least on good aircooling without too much trouble, with extreme cooling 3.5-3.7 is possible. At the same clockspeed, Brisbane G2 loses out to Windsor F3 by roughly 0.1Ghz, meaning Brisbane must clock an extra 0.1Ghz to be even with a Windsor.

I think my rams limit my OC.
Better grab 10th ann.

ha, better check properly
IMHO , if your balistix cannot make it, 10th probably can't make it as well
so what's your problem actually?

This post has been edited by dblooi: Dec 16 2007, 10:14 PM

try increase A BIT ram voltage...

omg...i really want to change to 690 already...who wana buy hard disks?????

im not using the f3 from the 2nd bulk.

btw,does anyone knows,why my pc cant be switched on? even cant load the bios. im facing a problem of my pc keep on switch on-off-on-off till i switch off the plug. last time,lohwenli told me,am2 mobo is very sensitive with the memory timing... is the timing that he meant is for FSB or for RAM??

yesterday,i've OCed till 2.5ghz with 1.35v, ram to 533 with 2.15v. orthos run for 2 hours,stable. then i switched off my pc during nite. just now morning turn it on,got the problem. need to clear CMOS back again~

does anyone using the same mobo with me encounter it before? or is it my RAM that holding me back from OC?

btw, im using Corsair valueram & mobo Biostar TA690G

Wat kind of hard disks?