im already rugi...but i think 2.2vdimm is good enuf for now to reach ddr1200, but with loose timing...waitin new amd mobo...then ill let go my mobo(cheap2!!)...people dun make mistake like what i did..

I think the most practical for daily use is only 3.2Ghz with Air Cooling.

Got my "Spider" yesterday...

Will try to O.C. after sorting out few bugs
Phenom X4 9500 | shaunk86 | MSI K9A2 Platinum | Crucial Ballistix Tracer 6400 | Stock HSF

[attachmentid=352683]

As bro -pws- wish. Here's again my ss.



Thanx for adding. 

---

Added on December 3, 2007, 8:22 am

haha. wait for me to learn more bout ram timing or perhaps changing my ram, i might surpass everyone for G1 core. hehehe. 

bro xixo. here's the memset ss.

Now, start from here, wat do i do? erm.. CL5 means what bro?

orite.

U mean, i use the same divider(ddr 400) but then loose the timing to 5-5-5-15-20-2T?

I had just finished my trial and error session. Apparently, i think my ram is limiting me.

I tried to start OC back from scratch(fsb=200Mhz), this time i set the multiplier to 10 and the ram divider to ddr400 so that it becomes 1:1. Set ram to 5-5-5-15-20-2T trfc0=195 MAL=10.

Everything went smoothly indeed until i went more than 260 fsb. Note that my ram was also at 260Mhz. Even 261 fsb, super pi 512K pon x lepas. I played with vcore,vdimm nothing worked.

FYI, My last OC the ram cannot pass 260Mhz as well, no matter what i do. The ram is still in its underclocked state but cannot go higher.
So weird lah . Rase cam nk campak my ram to loji tahi near my house .

So i guess the highest i cud go with my proc and my stupid ram for the time being is 2835Mhz with Fsb 270 X 10.5. 

thanx 
I think it's bcoz i did LOTS of trials and errors during my OC and eventually the chip becomes better hahah.. 
Kinda funny bcoz initially i thot i had a very bad brisby. Cant even pass 2.6. That was the time i had not discovered ram timing yet.
Lots of thanx to bro xixo_12. He helped me with the timing. 

use this one easy...

come on guys...
prime 24 hours before post result... those clock all fake =P

HAhahhaa well said bro.......I will not gamble my hardware for orthos 24h...my system is Stabil.No issue what so ever..
But who use Prime anymore nowdays??
Old program single threaded...Orthos or OCCT is better...

My 1st time OC 

After 26 Hour Orthos 

OK ka?? 

i tested my system..
cannot go to 3500.. prime few second only it hang liao... pump vcore to 1.550 also won't help...
finding the highest stable it can go temporary.......

buy my proc la... 3600+ can clock 3040mhz stable 24 hours.... =P

Set multiplier to 10 so that it becomes 1:1. Try use DDR400 divider. Set your trfc dimm *0/1/2/3(* the slots u put your ram) to 195 and change MAL value to 10. Start OC back from scratch with this setting. Bout the vcore, ive no idea why i only needed little vcore to push FSB at 310Mhz. Maybe i had better luck than you when getting the proc i guess. 

my board limited 2.3 too!
not enought for hungry oc'er

huhu, forgot you are diehard OCer 
make sure u won't Vmod the Vdimm till 3V or else....kaboom...asap keluar! 

bro, tu pki WC ke on air jek

wahaha, congratulation bro~!
marching to 22sec next 

btw, just checked the pi 1M thread, adi 8 F3 guys in top 10 

http://forum.lowyat.net/topic/321443

edited: bro xixo , try to use memset 3.3    , this memset 3.4 beta sucks for am2 ram tweaking