bro ianho,
mind to show how u test it cos the temp will be different if you test outsude of casing and inside close casing...

btw different between 20c is very impressive..

Offcourse it is, look at the original 8800 series heatsink.
Not just the stock heatsink only use 1 heatpipe, the stock heatsink cools everything using ONLY 1 heatsink A.K.A. All In One.

While for HR-03, everything is separated, thus, it cools every single parts each by using it's own heatsink.

Imagine that you're in 1HP airconditioned room in these two case, which one is cooler and which is not?
* You are alone inside the aiconditioned room.
* You're with 30 of your friend inside the aiconditioned room.

20c for 100 buck i wouldnt mind to pay for it..
is there any official release price for hr03 plus in the market as i far away from ly plaza and seldom check price list.. :lol

hmmm ... so u had a bad experience with him also ??

I had mine for a very minor item only ..

treat customers so badly even after many times of return purchase ...


more supplier would make the market more healthier ....

You mean the existing TR bulker right? Yeah, really bad attitude. No sense of trading at all.

However, I did see a few new TR bulker in garage sales.... their prices are not much different, minus the attitude, I'll get from them anytime!!!

This post has been edited by kmarc: Sep 23 2007, 10:30 AM

aiyaa.. wait til 2020, by that time mebi gone ady

btw, since u change the GFx stock cooling, still can do SLi meh? can the hr03 fit between both GFx?

I really if uncle's test setup can be fit into a standard atx case to let us know how it would fit into a case ....

I don't have any bad experience with him, but a good friend of mine were treated badly there.

Can, but u hafta use the slim type of 80mm fan if using for SLI.




Shud be able to lar. The top of the IFX14 doesn't go above the the PCB of the mobo n the bottom HR03 only goes slightly below the bottom of the mobo PCB with a slim 8cm fan. Most ATX cases got about 2-3cm clearance at the bottom sumore. Only thing is the height of the IFX14 is incredible. It's like KL Tower! So narrow cases wont fit. If follow ATX spec then sudn be a prob I reckon. aAnyway, after I finish testing n benching I will take out everything n squeeze it all into an Encloxure Wizard casing to see if allthose heatpipes will go inside a normal ATX case.

Damn, ianho is really making everyone wished to be sponsored in a way..LOL..

I am sensing a massive TR setup coming really soon. I really love to see the final setup. Fast fast post some wonderful heatpipe fetish setup...

it purely depends on the distance between ur PCI-ex slots

Yea, and with the distance of PCIE slot for the Striker Extreme, it should be able to fit. However, i am sensing that he will need to sacrifice quite a number of PCI slots when doing so..

Wahhhhhhhhhhhhhhhhhhhh jeoulessssssssssssssnyaaaaaaaaaaaaaaa meeeeeeeeeeeeee

Muahahahahahahahahhahaha. My Quad core Q6600 is now running OCCT at 4ghz! I dedicate this 4ghz run to Inter Asia n Thermalright. Without them this 4ghz run would not be possible. Thank you, thank you, thank you.

Screenshots coming right up.

Here's the screenshot of the Q6600 running OCCt at 4ghz. Halfway tru OCCT.











Here's the screenshot of OCCT stable. Finished the run nicely.

then if run at QX6850 then how le~!~

Same oso lar I think. Just mebe dont need such high Vcore n temps wont be so high oni. U take 1 n test lar. U got 2 units right?

Uncle!
I demand CPUz screenie!

Can't believe a 680i chipset based motherboard has the capability of pushing a Q6600 G0 to 506MHz X 8.

there is where i need to correct ya
probably will not be able to as the QX 6850 runs way hotter due to the etra 10W TDP

*edit, found out its more than 10W that means more heat
my X6800 idles more than 10 degrees hotter than E66s and E67s, and my TDP is only 10W higher ><

This post has been edited by DaRkSyThE: Sep 23 2007, 07:22 PM

That is stock to stock comparo. How can u compare stock to stock when it's OCed?